GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
Total records found: 319
arrow-prev 1 … 10 11 12 13 arrow-next
prEN 489-1 Public enquiry
Comment end date 2026-10-24
District heating pipes - Bonded single and twin pipe systems for buried hot and coldwater networks - Part 1: Joint casing assemblies and thermal insulation for hot and cold-water networks with metal service pipes in accordance with EN 13941-series.

This document specifies requirements and test methods for joint casing systems for single and twin pipes between adjacent factory-made pipe, and/or fitting and/or valve assemblies for buried heating and cooling water networks with rigid pipe systems with metal service pipes in accordance with EN 13941-1 [4] and EN 13941-2 [5] as well as rigid pipe systems with plastic service pipes according to series EN 17415 and flexible pipe systems with metal service pipes according to EN 15632-4 . NOTE There are no differences in requirements for single and twin pipe joint casing systems. For bedding materials other than those defined in 5.2.3 additional precautions are defined inEN 13941-2 [5].

prEN 301 908-26 V1.0.0 (2026-08) Public enquiry
Comment end date 2026-11-09
IMT cellular networks; Harmonised Standard for access to radio spectrum; Part 26: Aerial User Equipment (UE)
prEN IEC 63758-5-3:2026 Public enquiry
Comment end date 2026-11-22
Qi specification - Version 2.3 - Part 5-3: Mpp - Magnetics design (Fast Track)
prEN ISO 21043-2 Public enquiry
Comment end date 2026-12-12
Forensic sciences - Part 2: General requirements for the forensic process, and the recovery and management of items (ISO/DIS 21043-2:2026)

This document specifies general requirements and recommendations for the operation of the forensic service provider. These apply throughout the forensic process, both at a scene and within a facility. This document also contains requirements and provides recommendations for the recovery and management of items. These requirements and recommendations are designed to ensure that: — items are preserved; — personnel are competent; — equipment and consumables are suitable; — health and safety risks are mitigated. This document is applicable to all areas of expertise of forensic science; however, it is not applicable to the recovery of digital data, which is covered by ISO/IEC 27037.[1] The storage medium itself can yield additional items (e.g. fingermarks or DNA) which would be covered by this document.

prEN IEC 60447:2026 Archived
Comment end date 2026-10-16
Basic and safety principles for man-machine interface, marking and identification - Actuating principles
prEN 304 625 V1.0.0 (2026-08) Public enquiry
Comment end date 2026-10-26
Cyber Security (CYBER); CRA; Cybersecurity requirements for physical and virtual network interfaces
prEN IEC 60598-2-5:2026 Public enquiry
Comment end date 2026-11-08
Luminaires - Part 2-5: Particular requirements - Floodlights
EN 1993-1-6:2025/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 3 - Design of steel structures - Part 1-6: Strength and stability of shell structures

1.1 Scope (1) EN 199316 provides rules for the structural design of plated steel structures that have the form of a shell of revolution (axisymmetric shell). (2) This document is applicable to unstiffened fabricated axisymmetric shells formed from isotropic rolled plates using both algebraic and computational procedures, and to stiffened axisymmetric shells with different wall constructions using computational procedures. It also applies to associated circular or annular plates and to beam section rings and stringer stiffeners where they form part of the complete shell structure. The general computational procedures are applicable to all shell forms. (3) This document does not apply to manufactured shells or to shell panels or to elliptical shell forms, except that its computational procedures are applicable to all shell structures. This document does not apply to structures under seismic or other dynamic loading. It does not cover the aspects of leakage of stored liquids or solids. (4) Cylindrical and conical panels are not explicitly covered by this document. However, the provisions of 9.8 can be used provided that appropriate boundary conditions are taken into account. (5) This document defines the characteristic and design values of the resistance of the structure. (6) This document is concerned with the requirements for design against the ultimate limit states of: — plastic failure; — cyclic plasticity; — buckling; — fatigue. (7) Overall equilibrium of the structure (sliding, uplifting, overturning) is not included in this document. Special considerations for specific applications are included in the relevant application parts of EN 1993. (8) Detailed formulae for the simple calculation of unstiffened cylinders, cones and spherical domes are given in the Annexes. (9) Provisions for simple calculations on specific stiffened shell types are given in EN 199341. (10) This document is intended for application to steel shell structures. Where no standard exists for shell structures made of other metals, including high strength steels, the provisions of this document are applicable provided the appropriate material properties of the metal are taken into account. (11) The provisions of this document are intended to be applied within the temperature ranges defined in the relevant EN 1993 application parts. (12) Where no application part defines a different range, this document applies to structures within the following limits: — design metal temperatures lie within the range −50 °C to +100 °C, except when using the special provisions given in 5.1; — radius to thickness ratios (r/t) within the range 50 to 2 000; — manufactured circular hollow sections according to EN 10210 and EN 10219 are outside the scope of this document and are covered by EN 199311. However, if no other provisions are available, the rules of this document are useful for manufactured circular hollow sections. In particular, this document is applicable to the design of manufactured piles (see EN 19935) provided the imperfections and tolerance requirements of EN 19935 are adopted in place of those specified in this document, and where no other standard covers the specific pile geometry. NOTE 1 Experimental and theoretical data relating to manufactured circular hollow sections were not considered when this document was drafted. The application of this document to such structures therefore remains the responsibility of the user. NOTE 2 The stress design rules of this document can be rather conservative if applied to some geometries and loading conditions for relatively thickwalled shells. NOTE 3 Thinner shells than r/t = 2 000 can be treated using these provisions but the provisions have not been verified for such thin shells. NOTE 4 The maximum temperature is restricted so that the influence of creep can be ignored where high temperature creep effects are not covered by the relevant application part. [...]

prEN IEC 60335-2-83:2026 Public enquiry
Comment end date 2026-11-29
Household and similar electrical appliances - Safety - Part 2-83: Particular requirements for heated gullies for roof drainage

This European standard deals with the safety of electrically heated gullies for de-icing the inlet of the drainage system of flat roofs, balconies, and similar structures, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances.

prEN ISO 8503-5 Public enquiry
Comment end date 2026-10-29
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 5: Replica tape method for the determination of the surface profile (ISO/DIS 8503‑5:2026)

ISO 8503-5:2017 describes a field method for measuring the surface profile produced by any of the abrasive blast-cleaning procedures given in ISO 8504-2. The method uses replica tape and a suitable gauge for measuring, on site, the roughness of a surface before the application of paint or another protective coating. The method is applicable within the range of profile heights cited for a given grade (or thickness) of replica tape. The commercial grades currently available permit measurement of average peak-to-valley profiles of 20 µm to 115 µm. The method is valid for surfaces that have been cleaned with abrasives.

prEN 319 142-1 V1.3.0 (2026-08) Public enquiry
Comment end date 2026-10-27
Electronic Signatures and Trust Infrastructures (ESI); PAdES digital signatures; Part 1: Building blocks and PAdES baseline signatures
prEN IEC 63567-3:2026 Public enquiry
Comment end date 2026-11-15
Semiconductor devices - Performance evaluation of semiconductor processing components and inspection equipment - Part 3: Nano-scale wafer surface inspection method using UV light
prEN IEC 63758-7:2026 Public enquiry
Comment end date 2026-11-22
Qi Specification - Version 2.3 - Part 7: Magnetic covers (Fast Track)
prEN 16883 Public enquiry
Comment end date 2026-12-03
Conservation of cultural heritage - Guidelines for improving the energy performance of historic buildings

This document provides guidelines for sustainably improving the energy performance of historic buildings, e.g. historically, architecturally or culturally valuable buildings, while respecting their significance. The use of this document is not limited to buildings with statutory heritage designation, it applies to historic buildings of all types and ages. This document presents a normative working procedure for selecting measures to improve energy performance, based on an investigation, analysis and documentation of the building including its significance. The procedure assesses the impact of those measures in relation to preserving the character-defining elements of the building.

prEN ISO 15384 Public enquiry
Comment end date 2026-11-20
Protective clothing for firefighters - Laboratory test methods and performance requirements for wildland firefighting clothing (ISO/DIS 15384:2026)

This document specifies methods of test and minimum performance requirements for personal protective clothing, designed to protect the wearer's body, except for the head, hands, and feet, that is worn during wildland firefighting and associated activities. This clothing is not intended to provide protection during fire entrapment. This document covers the general design of the garment, the minimum level of performance for the materials employed and the methods of test to determine these levels. This document is not applicable to clothing for use in situations encountered in structural firefighting (EN 469 or ISO 11999-3), rescue (ISO 18639) or where a high level of infrared radiation is expected (ISO 15538 or EN 1486), nor does this document cover clothing to protect against chemical, biological, electrical or radiation hazards. This document does not provide protection against high mechanical risks such as for protection when using chain saws.

prEN IEC 62087-1:2026 Archived
Comment end date 2026-10-18
Audio, video, and related equipment - Determination of power consumption - Part 1: General
prEN IEC 60335-2-67:2026 Public enquiry
Comment end date 2026-11-08
Household and similar electrical appliances - Safety - Part 2-67: Particular requirements for floor treatment machines, for commercial use

This standard deals with the safety of powered floor treatment machines intended for commercial indoor or outdoor use for the following applications: - scrubbing, - wet or dry pick-up, - polishing and dry buffing, - application of wax, sealing products and powder based detergents, - shampooing, - stripping, grinding and scarifying of floors with an artificial surface. These machines have a cleaning motion which is more lateral or periodic than linear. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: - public use areas such as hotels, schools, hospitals; - industrial locations, for example factories and manufacturing shops; - retail outlets, for example shops and supermarkets; - business premises, for example offices and banks; - all uses other than normal housekeeping purposes. These machines are not equipped with a traction drive. The following power systems are covered: - internal combustion engines, - mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, - battery-operated machines. Battery-operated machines may be equipped with a built-in battery charger.

prEN IEC/IEEE 80005-3:2026 Public enquiry
Comment end date 2026-11-15
Utility connections in port - Part 3: Low-voltage shore connection (LVSC) systems - General requirements

This document specifies provisions for the design, installation and testing of low-voltage shore connection (LVSC) systems, onboard ships and on shore, to supply the ship with electrical power from shore. This document is applicable to: – ships requiring up to 1 MVA while at berth; – three-phase shore connection systems rated 250 A and above, and with a nominal voltage rating of 400 V AC to 1 000 V AC; – shore-side connection systems; – shore-to -ship connection and interface equipment; – transformers and reactors; – semiconductor and rotating frequency convertors; – ship-side connection systems; – protection, control, monitoring, interlocking and power management systems. This document does not apply to: – inland navigation vessels; – high-voltage shore connection systems, including ships built in accordance with the annexes of IEC/IEEE 80005-1; – the electrical power supply during docking periods, for example dry docking and other out-of-service maintenance and repair; – systems to be operated by ordinary persons as defined in 3.19. NOTE 1 Other standards are available specifically for inland navigation vessels in Europe. NOTE 2 IEC 6 0092-507 is applicable to small vessels. NOTE 3 Additional or alternative requirements can be imposed by national administrations or the authorities within whose jurisdiction the ship is intended to operate and by the owners or authorities responsible for a shore power supply or distribution system. NOTE 4 High-voltage shore connection systems are covered by IEC/IEEE 80005-1. NOTE 5 Some existing 380 V AC ship systems can be supplied by 400 V AC.

prEN ISO 15883-4 Public enquiry
Comment end date 2026-11-26
Washer-disinfectors - Part 4: Requirements and tests for washer-disinfectors employing chemical disinfection for thermolabile endoscopes (ISO/DIS 15883-4:2026)

This document specifies the particular requirements, including performance criteria for washer-disinfectors (WD) that are intended to be used for cleaning and chemical disinfection of thermolabile endoscopes. This document also specifies the performance requirements for the cleaning and disinfection of the washer-disinfector and its components and accessories which can be required to achieve the necessary performance criteria. The methods, instrumentation and instructions required for type testing, works testing, validation (installation, operational and performance qualification on first installation), routine control and monitoring, and requalification of WD periodically and after essential repairs, are also specified. NOTE 1 In addition, Annex A gives guidance on an appropriate division of responsibility for the range of activities covered by this document. NOTE 2 WD complying with this document can also be used for cleaning and chemical disinfection of other thermolabile re-usable medical devices for which the device manufacturer has recommended and validated this method of disinfection. WD complying with the requirements of this document are not intended for cleaning and disinfection of medical devices, including endoscopic accessories, which are heat stable and can be disinfected or sterilized by thermal methods (see ISO 15883-1:2006+Amd 1:2014, 4.1.5). The specified performance requirements of this document do not ensure the inactivation or removal of the causative agent(s) (prion protein) of transmissible spongiform encephalopathies. NOTE 3 If it is considered that prion protein might be present, particular care is needed in the choice of cleaning agents and disinfectants to ensure that the chemicals used do not react with the prion protein and/or other protein in a manner that can inhibit its removal or inactivation from the load or washer-disinfector. NOTE 4 This document can be used by prospective purchasers and manufacturers as the basis of agreement on the specification of the WD, manufacturers of endoscopes, cleaning products, and disinfecting products.

prEN IEC 62228-5:2026 Public enquiry
Comment end date 2026-12-04
Integrated circuits - EMC evaluation of transceivers - Part 5: Ethernet transceivers
prEN ISO 12217-2 Public enquiry
Comment end date 2026-10-25
Small craft - Stability and buoyancy assessment and categorization - Part 2: Sailing boats (ISO/DIS 12217-2:2026)

This document specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed. The evaluation of stability and buoyancy properties using this document will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum load. This document is principally applicable to boats propelled primarily by sail (even if fitted with an auxiliary engine) of 6 m up to and including 24 m hull length. However, it can also be applied to boats less than 6 m if they are habitable multihulls or can be applied if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812. In relation to habitable multihulls, this document includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation. This document excludes: —    inflatable and rigid-inflatable boats covered by the ISO 6185 series, except for references made in the ISO 6185 series to specific clauses of the ISO 12217 series; —    gondolas and pedalos; —    surfboards including sailing surfboards; and —    hydrofoils and foil stabilized boats when not operating in the displacement mode. NOTE       Displacement mode means that the boat is only supported by hydrostatic forces. It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

prEN IEC 60335-2-73:2026/prAA:2026 Archived
Comment end date 2026-10-18
Household and similar electrical appliances - Safety - Part 2-73: Particular requirements for fixed immersion heaters

This standard deals with the safety of electric thermal-storage room heaters intended to heat the room in which they are located, their rated voltage being not more than 250 V for single phase and 480 V for other appliances.

prEN IEC 60335-2-72:2026/prAA:2026 Public enquiry
Comment end date 2026-11-08
Household and similar electrical appliances - Safety - Part 2-72: Particular requirements for floor treatment machines with or without traction drive, for commercial use

his Document deals with the safety of powered ride-on and powered walk-behind machines intended for commercial indoor or outdoor use for the following applications: - sweeping, - scrubbing, - wet or dry pick-up, - polishing, - application of wax, sealing products and powder-based detergents, - shampooing of floors. These machines have a cleaning motion which is more linear than lateral or periodic. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: - public use areas such as hotels, schools, hospitals; - industrial locations, for example factories and manufacturing shops; - retail outlets, for example shops and supermarkets; - business premises, for example offices and banks; - all uses other than normal housekeeping purposes. These machines may be equipped with a traction drive system. The following power systems are covered: - internal combustion engines, - mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, - battery-operated machines. Battery-operated machines may be equipped with a built-in battery charger. This standard does not apply to - floor treatment appliances for household use (IEC 60335-2-10); - floor treatment machines for commercial use (IEC 60335-2-67); - spray extraction machines for commercial use (IEC 60335-2-68); - wet and dry vacuum cleaners, including power brush, for commercial use (IEC 60335-2-69); - road sweepers; - machines designed for use on slopes with a gradient exceeding 20 %; - machines equipped with a power take-off (PTO); - machines designed for use in corrosive or explosive environments (dust, vapour or gas); - machines designed for picking up hazardous dusts (as defined in IEC 60335-2-69), inflammable substances, or glowing particles; - machines designed for use in vehicles or on board of ships or aircraft.

prEN 1538 Public enquiry
Comment end date 2026-11-05
Execution of special geotechnical work - Diaphragm walls

This European Standard establishes general principles for the execution of diaphragm walls as either retaining walls or cut-off walls. NOTE 1 This standard covers only structures constructed in a trench excavated with a support fluid or in dry conditions, where soil is removed and replaced by concrete or slurry and with wall thickness B ≥ 40 cm. NOTE 2 Diaphragm walls can be permanent or temporary structures. NOTE 3 The following types of structure are considered: a) retaining walls: usually constructed to support the sides of an excavation in the ground. They include: 1) cast in situ concrete diaphragm walls; 2) precast concrete diaphragm walls; 3) reinforced slurry walls; b) cut-off walls: usually constructed to prevent migration of groundwater, clear or polluted, or of other contaminants present in the ground. They include: 1) slurry walls (possibly with membranes or sheet piles); 2) plastic concrete walls. NOTE 4 Walls formed shallow vertical trenches (typically excavations with a ratio of depth over thickness D/B < 5 or D < 5 m) are not covered by this standard.

prEN ISO 13356 Public enquiry
Comment end date 2026-10-31
Implants for surgery - Alumina ceramic material: Zirconia - Yttria-stabilized tetragonal zirconia (Y-TZP) (ISO/DIS 13356:2026)

This document specifies the requirements and corresponding test methods for a biocompatible and bio-inert ceramic bone-substitute material based on yttriastabilized tetragonal zirconia (yttria tetragonal zirconia polycrystal, Y-TZP) for use as a material for surgical implants.

Total records found: 319
arrow-prev 1 … 10 11 12 13 arrow-next

Quick filters

Technical Committee
TK 1 Electronics (34) TK 4 Information technology (4) TK 5 Electrical engineering (42) TK 9 Furniture (2) TK 13 Agricultural engineering (4) TK 18 Telecommunications (15) TK 20 Toys, child use articles, sports and other recreational equipment (1) TK 21 Textiles and personal protective equipment (2) TK 22 Fire safety (7) TK 23 Ceramic tiles, masonry and natural stones (1) TK 24 Quality management and quality assurance (2) TK 25 Matrix, gypsum and gypsum based products (1) TK 26 Thermal insulation materials (1) TK 29 Water supply (16) TK 32 Health (10) TK 35 Safety of machinery (2) TK 36 Environmental protection (2) TK 38 Building constructions (14) TK 39 Protection (2) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (2) TK 41 Welding (8) TK 45 Electric power (6) TK 46 Roofs and building waterproof isolation (6) TK 49 Metallic materials (6) TK 50 Heating and Ventilation Systems (2) TK 51 Food analysis- Horizontal methods (1) TK 56 Metal liquid tanks and industrial pipelines (1) TK 57 Fertilizers (3) TK 59 Geotechnics (3) TK 60 Windows and doors (4) TK 68 Plastics (7) TK 70 Pulp, paper, board, adhesives (1) TK 76 Explosive atmospheres (6) TK 77 Lifts (1) TK 79 IT security techniques (3) TK 80 Road transport and traffic telematics (1) TK 81 Conservation of cultural property (1) TK 82 Safety of trackless overground vehicles (2) TK 86 Geographic information (1) TK 87 Biotechnology (8) TK 88 Building Information Modelling (BIM) (1) TK 89 Risk management and organizational governance (1) TK 91 Asset management and technical maintenance (2) TK 94 Circural economy (1) TK 99 Health Informatics (2)
ICS
Hidrologinės dirvožemio savybės (1) Acid secondary cells and batteries (3) Adhesives (1) Aerospace electric equipment and systems (3) Alarm and warning systems (1) Alcohols. Ethers (1) Aluminium products (1) Amplifiers (3) Anaesthetic, respiratory and reanimation equipment (6) Application of information technology in general (2) Binders. Sealing materials (1) Biology. Botany. Zoology (8) Boilers and heat exchangers (1) Brazing and soldering (1) Building accessories (1) Cellular materials (1) Cement. Gypsum. Lime. Mortar (2) Chemical laboratories. Laboratory equipment (4) Chemicals for purification of water (9) Cleaning appliances (7) Cleanrooms and associated controlled environments (1) Coaxial cables. Waveguides (1) Colour coding (1) Cranes (1) Dental implants (1) Diagnostic equipment (1) Domestic safety (8) Earthworks. Excavations. Foundation construction. Underground works (3) Electric road vehicles (3) Electrical and electronic equipment (2) Electrical and electronic equipment. Control systems (1) Electrical and electronic testing (1) Electrical apparatus for explosive atmospheres (4) Electrical engineering in general (1) Electrical equipment of ships and of marine structure (1) Emission (1) Environment. Health protection. Safety (Vocabularies) (1) Environmental economics. Sustainability (1) Equipment for children (1) Exploratory, drilling and extraction equipment (2) Fertilizers (2) Fibre optic interconnecting devices (1) Fibres and cables (2) Fire protection (1) Fire-fighting (4) Fire-resistance of building materials and elements (1) Floor coverings (2) Food microbiology (1) Forensic science (1) Furniture (2) Fuses and other overcurrent protection devices (2) Gas cylinders (1) Gas heaters (1) Geometrical Product Specification (GPS) (1) Governance and ethics (1) Hand-operated tools (1) Home economics in general (2) Identification cards. Chip cards. Biometrics (1) Immunity (1) Implants for surgery, prosthetics and orthotics (1) Insulators (1) Integrated circuits. Microelectronics (2) Iron and steel pipes (1) IT applications in health care technology (1) IT applications in information, documentation and publishing (1) IT applications in science (2) IT applications in transport (1) IT Security (4) Items of art and handicrafts. Cultural property and heritage (1) Laminated sheets (1) Laundry appliances (2) Leather and furs (2) Lifts. Escalators (1) Lines, connections and circuits (1) Liquid fuels (1) Luminaires (3) Maintenance services. Facilities management (2) Mechanical testing of metals (1) Mining equipment in general (1) Miscellaneous domestic and commercial equipment (1) Multilayer applications (1) Navigation and control equipment (1) Networking (1) Non-ferrous metal pipes (2) Other fluid power system components (1) Other kitchen equipment (1) Other semiconductor devices (2) Other standards related to lamps (1) Paints and varnishes (2) Petroleum products and natural gas handling equipment (1) Pipelines and its parts for district heat (1) Plastics in general (2) Playgrounds (3) Power transmission and distribution networks in general (1) Primary cells and batteries (2) Printed circuits and boards (3) Product and company certification. Conformity assessment (1) Product life-cycles (1) Properties of surfaces (1) Protection against crime (1) Protection against falling and slipping (1) Protective clothing (1) Pumps (2) Radiographic equipment (1) Refrigerating technology (1) Reinforced plastics (1) Relays (1) RF connectors (2) Rivets (1) Road equipment and installations (1) Roofs (1) Safety of machinery (1) Seismic and vibration protection (1) Small craft (2) Smart textiles (1) Stainless steels (2) Stationary containers and tanks (1) Steel structures (3) Sterilization and disinfection in general (1) Sterilizing equipment (1) Surface preparation (4) Technical aspects (6) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (15) Telecontrol. Telemetering (1) Textile fabrics (1) Thermal and sound insulating materials (6) Thermoplastic materials (1) Timber structures (1) Transformers. Reactors (2) Ventilation and air-conditioning systems (1) Ventilators. Fans. Air-conditioners (3) Walls. Partitions. Façades (3) Water heating equipment (2) Water supply systems (7) Welded joints and welds (5) Welding equipment (2) Wires (11)