GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
Total records found: 319
arrow-prev 1 … 8 9 10 11 12 … 13 arrow-next
EN 55016-1-6:2015/prA3 (Frag 4):2026 Public enquiry
Comment end date 2026-10-25
Amendment 3 - Fragment 4: NSA
prEN IEC 60335-2-68:2026 Public enquiry
Comment end date 2026-11-08
Household and similar electrical appliances - Safety - Part 2-68: Particular requirements for spray extraction machines, for commercial use

This standard deals with the safety of electrical portable, non-self-propelled motor-operated spray extraction machines with or without attachments and with or without electrical heating elements, intended for commercial indoor use. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: - public use areas such as hotels, schools, hospitals; - industrial locations, for example factories and manufacturing shops; - retail outlets, for example shops and supermarkets; - business premises, for example offices and banks; - rental services for those machines; - all uses other than normal housekeeping purposes. The following power systems are covered: - mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, - battery-operated machines. This standard applies to machines in which the pressure of the employed cleaning agent does not exceed 2,5 MPa, and in which the product of the pressure (in MPa) and the flow of cleaning agent (in litres per minute) does not exceed 100, and in which the temperature of the cleaning agent at the spray nozzle outlet does not exceed 85 °C. This standard does not apply to - vacuum cleaners and water-suction cleaning appliances for household use (IEC 60335-2-2); - floor treatment machines for commercial use (IEC 60335-2-67, IEC 60335-2-72); - wet and dry vacuum cleaners, including power brush, for commercial use (IEC 60335-2-69); - hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series). - machines designed for use in corrosive or explosive environments (dust, vapour or gas); - machines designed for picking up hazardous dusts (as defined in IEC 60335-2-69), inflammable substances, or glowing particles; - machines designed to handle hazardous solvents, such as flammable or explosive liquids;

prEN IEC 63281-5-1:2026 Public enquiry
Comment end date 2026-11-03
Interface requirements of autonomous cargo e-Transporters and cloud platform scheduling system
prEN IEC 63758-1-2:2026 Public enquiry
Comment end date 2026-11-22
Qi specification - Version 2.3 - Part 1-2: General - Glossary (Fast Track)
prEN IEC 62228-3:2026 Public enquiry
Comment end date 2026-12-04
Integrated circuits - EMC evaluation of transceivers - Part 3: CAN transceivers
prEN ISO 13350 Public enquiry
Comment end date 2026-11-14
Fans - Performance testing of jet fans in a laboratory (ISO/DIS 13350:2026)

ISO 13350:2015 deals with the determination of those technical characteristics needed to describe all aspects of the performance of jet fans as defined in ISO 13349. It does not cover those fans designed for ducted applications, nor those designed solely for air circulation, e.g. ceiling fans and table fans. The test procedures described in this International Standard relate to laboratory conditions. The measurement of performance under on-site conditions is not included.

prEN ISO 8502-2 Archived
Comment end date 2026-10-17
Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 2: Extraction of water-soluble contaminants for analysis by swabbing method (ISO/DIS 8502‑2:2026)

ISO 8502-2:2017 describes a method for the determination of chloride-containing salts that are readily soluble in water and are present on a steel surface. The method is also applicable to previously coated surfaces. ISO 8502-2:2017 includes a method, applicable in the field or in the laboratory, for washing off the surface while several methods are referred to for chloride analyses.

prEN IEC 60335-2-69:2026/prAA:2026 Public enquiry
Comment end date 2026-11-08
Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush for commercial use

This standard deals with the safety of electrical motor-operated vacuum cleaners, including back-pack vacuum cleaners, and dust extractors, for wet suction, dry suction, or wet and dry suction, intended for commercial indoor or outdoor use with or without attachments. These machines may be provided with a blowing or inflating function. The inner diameter of the dust container connector to the suction hose shall not exceed 200 mm. It also deals with the safety of centrally-sited vacuum cleaners, excluding the installation of the system. Attention is drawn to the fact that additional requirements on the safe installation of centrally-sited vacuum cleaners are not addressed by this standard but need to be taken into account. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: – public use areas such as hotels, schools, hospitals; – industrial locations, for example factories and manufacturing shops; – retail outlets, for example shops and supermarkets; – business premises, for example offices and banks; – all uses other than normal housekeeping purposes. These machines are not equipped with a traction drive. The following power systems are covered: – mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, – battery-operated motors. This standard also applies to machines handling hazardous dust, such as asbestos, and combustible dust in other than an explosive dust atmosphere. Additional requirements for machines handling hazardous dust are given in normative Annex AA. Attention is drawn to the fact that in many countries additional requirements on hazardous substances might apply. Radioactive substances are not covered by definition of hazardous dust for the purposes of this standard. This standard does not apply to – vacuum cleaners and water-suction cleaning appliances for household use (IEC 60335-2-2); – floor treatment machines for commercial use (IEC 60335-2-67, IEC 60335-2-72); – spray extraction machines for commercial use (IEC 60335-2-68); IEC 60335-2-67 and IEC 60335-2-68 cover only machines without traction drive. – hand-held mains-operated electrical garden blowers, vacuums and blower vacuums (IEC 60335-2-100); – hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series); – appliances for medical purposes (IEC 60601-1); – machines designed for use in corrosive environments; – machines designed for picking up liquids with a flash point below 55 °C; – machines designed for use in explosive environments (dust, vapour or gas), except those designed for use in zone 22; – machines intended to vacuum ash from fireplaces, chimneys, ovens, ashtrays and similar places of ash accumulation.

EN IEC 61000-6-3/prA1:2026 Public enquiry
Comment end date 2026-11-15
Amendment 1 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for equipment in residential locations
prEN ISO 18082 Public enquiry
Comment end date 2026-11-26
Anaesthetic and respiratory equipment - Dimensions of non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases (ISO/DIS 18082:2026)

ISO 18082:2014 specifies the dimensions, the allocation and marking of non-interchangeable screw-threaded (NIST) connectors intended to be used at operating pressures up to 1 400 kPa, and for vacuum systems at pressures not greater than 60 kPa absolute. ISO 18082:2014 specifies NIST connectors intended for use with the following medical gases: oxygen; nitrous oxide; medical air; helium; carbon dioxide; xenon; specified mixtures of the gases listed above; oxygen-enriched air; air for driving surgical tools; nitrogen for driving surgical tools; use with vacuum.

ISO/DIS 37011 Public enquiry
Comment end date 2026-11-30
Purpose-driven organizations — Guidance

This document provides guidance on organizational purpose and governance of purpose-driven organizations - organizations that seek to align their decision-making and actions with the long-term wellbeing of all people and the planet. This document provides guidance to governing bodies on consciously directing, overseeing and accounting for how they govern their organizations so that it is purpose-driven. It is also intended to be relevant to stakeholders who provide services and support to organizations, or who invest in them, support them and help hold them to account for their purpose-driven commitments. It covers the worldviews, practices and behaviours of purpose-driven organizations and those that govern and influence them. This document is applicable to organizations of all types and sizes. This document does not provide guidance on organizational transformation processes.

prEN IEC 61010-2-033:2026 Public enquiry
Comment end date 2026-11-22
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-033: Particular requirements for hand-held multimeters and other meters for domestic and professional use, capable of measuring mains voltage
prEN 2593-001 Public enquiry
Comment end date 2026-10-31
Aerospace series — Bases for 10 A electromagnetic plug-in relays, two and four poles double thrown — Part 001: Technical specification

The present document specifies the characteristics, installation and mounting dimensions for plug-in relay bases for use with two and four poles double throw relays in accordance with EN 2548-001. Relay bases in accordance with this document shall be used at ambient temperatures between −70 °C and 125 °C and at altitudes up to 25 000 m.

prEN ISO 21037 Public enquiry
Comment end date 2026-10-24
Adhesives - Guideline for separating adhesively bonded joints enabling repair and improving recycling (ISO 21037:2026)

This document specifies the methods commonly available for separating adhesively bonded joints enabling repair and improving recycling. This document applies to adherends made of metallic and non-metallic inorganic material, plastics including both filler-containing and fibre-reinforced types, wood and wood-based materials, coated materials, adherends of natural and polymeric fibres as well as paper and cardboard.

ISO/DIS 24088-1 Public enquiry
Comment end date 2026-11-03
Biotechnology — Biobanking of microorganisms — Part 1: Bacteria and archaea

This document specifies requirements for the biobanking of bacteria and archaea. It includes management of microbial material associated data as well as biosafety and biosecurity requirements. This document is applicable to all organizations performing biobanking with bacteria and archaea used for research and development. This document does not apply to processing methods for microbial materials intended for food/feed production, laboratories undertaking food/feed analysis or therapeutic use. NOTE International, national or regional regulations or requirements, or multiple of them, can also apply to specific topics covered in this document.

EN 60317-80/prA1:2026 Public enquiry
Comment end date 2026-11-06
Amendment 1 - Specifications for particular types of winding wires - Part 80: Polyvinyl acetal enamelled rectangular copper wire, class 120, with a bonding layer
prEN 1489 Public enquiry
Comment end date 2026-11-22
Building valves - Pressure safety valves - Tests and requirements

This document specifies dimensions, materials and performance requirements, including methods of test, for pressure safety valves, of nominal sizes from DN 15 to DN 40, having working pressures from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Pressure safety valves are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95 °C. Pressure safety valves limit the pressure in hot water heaters. Pressure safety valves do not control the temperature and alone do not constitute the protection required for storage water heaters. They are not intended to act as expansion valves under normal conditions. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

prEN IEC 63758-12:2026 Public enquiry
Comment end date 2026-11-22
Qi Specification - Version 2.3 - Part 12: Active alignment system (Fast Track)
EN 50173-1:2018/prA1:2026 Public enquiry
Comment end date 2026-12-11
Information technology - Generic cabling systems - Part 1: General requirements

This European Standard specifies: a) the structure and configuration of the backbone cabling subsystems of generic cabling systems within the types of premises and/or spaces defined by the other standards in the EN 50173 series; b) channel transmission and environmental performance requirements in support of the standards in the EN 50173 series (which have taken into account requirements specified in application standards listed in Annex F); c) link performance requirements in support of the standards in the EN 50173 series; d) backbone cabling reference implementations in support of the standards in the EN 50173 series; e) component performance requirements in support of the standards in the EN 50173 series; f) test procedures to verify conformance to the cabling transmission performance requirements of the standards in the EN 50173 series.

prEN 17082 Public enquiry
Comment end date 2026-12-17
Domestic and non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW

This document specifies the requirements and test methods for the safety and efficiency of gas fired air heaters with or without a fan to assist the transportation of combustion air and/or flue gases. This document also applies to warm air heaters having forced draught burners. This document applies to Type A2, A3 appliances, with an input not exceeding 300 kW (net CV basis), intended for non-domestic use. This document also applies to Type B11, B11AS, B11BS, B12, B12AS, B12BS, B13, B13AS, B13BS, B14, B14AS, B14BS, B22, B23, B41, B41AS, B41BS, B42, B42AS, B42BS, B43, B43AS, B43BS, B44, B44AS, B44BS, B52, B53, C11, C12, C13, C21, C31, C32, C33, C41, C52, C53, C62 and C63 appliances with an input not exceeding 300 kW (net CV basis), intended for domestic and non-domestic use. The heated air can be delivered by means of ducting. This document applies only to appliances using the gaseous fuels of the second and third families as defined in EN 437. For second family gases, this includes H2NG blends containing up to 20 % hydrogen by volume, where the appliance is marked with the appropriate extended category (e.g. I2H, I2E, I2E(Y20)). This document does not apply to appliances intended to burn gases containing carbon monoxide or other toxic components. This document does not apply to: a) dual purpose air conditioning appliances (heating and cooling); b) appliances where the air is heated by an intermediate fluid; c) portable or transportable forced convection appliances; d) appliances fitted with manual or automatic means of adjusting the combustion products evacuation by means of flue dampers; e) appliances having multiple heating units with a single draught diverter; f) appliances fitted with more than one flue outlet; g) appliances fitted with gas boosters; h) C21 and C41 appliances for 3rd family gases. NOTE 1 Appliance Types (A, B and C) are classified in accordance with EN 1749. NOTE 2 For C41 appliances, see all requirements and test methods that are valid for C21 appliances, unless otherwise stated.

prEN ISO/IEC 80079-20-1 Public enquiry
Comment end date 2026-10-22
Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data (ISO/IEC DIS 80079-20-1:2026)

This document is published as a dual log standard and provides guidance on classification of gases and vapours. It describes a test method intended for the measurement of the maximum experimental safe gaps (MESG) for gas-air mixtures or vapour-air mixtures under normal conditions of temperature and pressure (20 °C, 101,3 kPa) so as to permit the selection of an appropriate group of equipment. This document also describes a test method intended for use in the determination of the auto-ignition temperature (AIT) of a vapour-air mixture or gas-air mixture at atmospheric pressure, so as to permit the selection of an appropriate temperature class of equipment. Values of chemical properties of materials are provided to assist in the selection of equipment to be used in hazardous areas. Further data may be added as the results of validated tests become available. The materials and the characteristics included in a table (see Annex B) have been selected with particular reference to the use of equipment in hazardous areas. The data in this document have been taken from a number of references which are given in the bibliography. These methods for determining the MESG or the AIT may also be used for gas-air-inert mixtures or vapour-air-inert mixtures. However, data on air-inert mixtures are not tabulated. Keywords: classification of gases and vapours, measurement of the maximum experimental safe gaps (MESG)

EN 61169-32:1999/prA1:2026 Public enquiry
Comment end date 2026-11-08
Radio-frequency connectors - Part 32: RF coaxial connectors with inner diameter of outer conductor 1,85 mm (0,072 in) with screw coupling - Characteristic impedance 50 ohms (type 1,85)
prEN 1487 Public enquiry
Comment end date 2026-11-23
Building valves - Hydraulic safety groups - Tests and requirements

This document specifies dimensions, materials and performance requirements, including methods of test, for hydraulic safety groups, of nominal sizes from DN 15 to DN 25, having working pressures from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Hydraulic safety groups are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95 °C. Hydraulic safety groups limit the pressure in hot water heaters, prevent the backflow of water into the main circuit and prevent the discharged water to get into contact with the water in the water heater. Hydraulic safety groups do not control the temperature. They ensure the hydraulic safety of water heaters if the mechanical resistance of the water heater remains at least equal to the rating pressure. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

prEN IEC 63758-8:2026 Public enquiry
Comment end date 2026-11-22
Qi Specification - Version 2.3 - Part 8: Foreign object detection (Fast Track)
prEN 12907 Public enquiry
Comment end date 2026-12-20
Products used for treatment of water intended for human consumption - Pyrolyzed coal material

This European Standard is applicable to pyrolyzed coal material used for treatment of water intended for human consumption. It describes the characteristics of pyrolyzed coal material and specifies the requirements and the corresponding test methods for pyrolyzed coal material. It gives information on its use in water treatment.

Total records found: 319
arrow-prev 1 … 8 9 10 11 12 … 13 arrow-next

Quick filters

Technical Committee
TK 1 Electronics (34) TK 4 Information technology (4) TK 5 Electrical engineering (42) TK 9 Furniture (2) TK 13 Agricultural engineering (4) TK 18 Telecommunications (15) TK 20 Toys, child use articles, sports and other recreational equipment (1) TK 21 Textiles and personal protective equipment (2) TK 22 Fire safety (7) TK 23 Ceramic tiles, masonry and natural stones (1) TK 24 Quality management and quality assurance (2) TK 25 Matrix, gypsum and gypsum based products (1) TK 26 Thermal insulation materials (1) TK 29 Water supply (16) TK 32 Health (10) TK 35 Safety of machinery (2) TK 36 Environmental protection (2) TK 38 Building constructions (14) TK 39 Protection (2) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (2) TK 41 Welding (8) TK 45 Electric power (6) TK 46 Roofs and building waterproof isolation (6) TK 49 Metallic materials (6) TK 50 Heating and Ventilation Systems (2) TK 51 Food analysis- Horizontal methods (1) TK 56 Metal liquid tanks and industrial pipelines (1) TK 57 Fertilizers (3) TK 59 Geotechnics (3) TK 60 Windows and doors (4) TK 68 Plastics (7) TK 70 Pulp, paper, board, adhesives (1) TK 76 Explosive atmospheres (6) TK 77 Lifts (1) TK 79 IT security techniques (3) TK 80 Road transport and traffic telematics (1) TK 81 Conservation of cultural property (1) TK 82 Safety of trackless overground vehicles (2) TK 86 Geographic information (1) TK 87 Biotechnology (8) TK 88 Building Information Modelling (BIM) (1) TK 89 Risk management and organizational governance (1) TK 91 Asset management and technical maintenance (2) TK 94 Circural economy (1) TK 99 Health Informatics (2)
ICS
Hidrologinės dirvožemio savybės (1) Acid secondary cells and batteries (3) Adhesives (1) Aerospace electric equipment and systems (3) Alarm and warning systems (1) Alcohols. Ethers (1) Aluminium products (1) Amplifiers (3) Anaesthetic, respiratory and reanimation equipment (6) Application of information technology in general (2) Binders. Sealing materials (1) Biology. Botany. Zoology (8) Boilers and heat exchangers (1) Brazing and soldering (1) Building accessories (1) Cellular materials (1) Cement. Gypsum. Lime. Mortar (2) Chemical laboratories. Laboratory equipment (4) Chemicals for purification of water (9) Cleaning appliances (7) Cleanrooms and associated controlled environments (1) Coaxial cables. Waveguides (1) Colour coding (1) Cranes (1) Dental implants (1) Diagnostic equipment (1) Domestic safety (8) Earthworks. Excavations. Foundation construction. Underground works (3) Electric road vehicles (3) Electrical and electronic equipment (2) Electrical and electronic equipment. Control systems (1) Electrical and electronic testing (1) Electrical apparatus for explosive atmospheres (4) Electrical engineering in general (1) Electrical equipment of ships and of marine structure (1) Emission (1) Environment. Health protection. Safety (Vocabularies) (1) Environmental economics. Sustainability (1) Equipment for children (1) Exploratory, drilling and extraction equipment (2) Fertilizers (2) Fibre optic interconnecting devices (1) Fibres and cables (2) Fire protection (1) Fire-fighting (4) Fire-resistance of building materials and elements (1) Floor coverings (2) Food microbiology (1) Forensic science (1) Furniture (2) Fuses and other overcurrent protection devices (2) Gas cylinders (1) Gas heaters (1) Geometrical Product Specification (GPS) (1) Governance and ethics (1) Hand-operated tools (1) Home economics in general (2) Identification cards. Chip cards. Biometrics (1) Immunity (1) Implants for surgery, prosthetics and orthotics (1) Insulators (1) Integrated circuits. Microelectronics (2) Iron and steel pipes (1) IT applications in health care technology (1) IT applications in information, documentation and publishing (1) IT applications in science (2) IT applications in transport (1) IT Security (4) Items of art and handicrafts. Cultural property and heritage (1) Laminated sheets (1) Laundry appliances (2) Leather and furs (2) Lifts. Escalators (1) Lines, connections and circuits (1) Liquid fuels (1) Luminaires (3) Maintenance services. Facilities management (2) Mechanical testing of metals (1) Mining equipment in general (1) Miscellaneous domestic and commercial equipment (1) Multilayer applications (1) Navigation and control equipment (1) Networking (1) Non-ferrous metal pipes (2) Other fluid power system components (1) Other kitchen equipment (1) Other semiconductor devices (2) Other standards related to lamps (1) Paints and varnishes (2) Petroleum products and natural gas handling equipment (1) Pipelines and its parts for district heat (1) Plastics in general (2) Playgrounds (3) Power transmission and distribution networks in general (1) Primary cells and batteries (2) Printed circuits and boards (3) Product and company certification. Conformity assessment (1) Product life-cycles (1) Properties of surfaces (1) Protection against crime (1) Protection against falling and slipping (1) Protective clothing (1) Pumps (2) Radiographic equipment (1) Refrigerating technology (1) Reinforced plastics (1) Relays (1) RF connectors (2) Rivets (1) Road equipment and installations (1) Roofs (1) Safety of machinery (1) Seismic and vibration protection (1) Small craft (2) Smart textiles (1) Stainless steels (2) Stationary containers and tanks (1) Steel structures (3) Sterilization and disinfection in general (1) Sterilizing equipment (1) Surface preparation (4) Technical aspects (6) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (15) Telecontrol. Telemetering (1) Textile fabrics (1) Thermal and sound insulating materials (6) Thermoplastic materials (1) Timber structures (1) Transformers. Reactors (2) Ventilation and air-conditioning systems (1) Ventilators. Fans. Air-conditioners (3) Walls. Partitions. Façades (3) Water heating equipment (2) Water supply systems (7) Welded joints and welds (5) Welding equipment (2) Wires (11)