GDPR

Mandatory cookies

Mandatory cookies enable the main website functions. Without the aforementioned cookies the website cannot function properly. These cookies can be turned off only by changing the browser settings.

Statistics cookies

Analytical cookies allow us to improve the website by collecting and providing information about its usage.

Newsletter subscription

projektai-lsd Lithuanian Standards Board
Portal for draft standards
Register

List of drafts

Extended search

till

Results

Showing:
Total records found: 319
arrow-prev 1 … 6 7 8 9 10 … 13 arrow-next
prEN IEC 60335-2-15:2026/prAA:2026 Public enquiry
Comment end date 2026-12-06
Household and similar electrical appliances - Safety - Part 2-15: Particular requirements for appliances for heating liquids

This European Standard deals with the safety of electrical appliances for heating liquids for household and similar purposes, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances. Some appliances in this standard are used for heating food

Read draft and comment View
prEN 15221-6 Archived
Comment end date 2026-10-08
Facility Management - Part 6: Area and space measurement

This document establishes a common basis for planning and design, area and space management, financial assessment, as well as a tool for benchmarking in the life cycle of the built asset. This document covers area and space measurement for existing owned or leased buildings as well as buildings in state of planning or development. This document establishes a framework to deal with area and space measurement to promote both the entire life cycle information requirements and the digital technologies used by the industry. In addition, it defines clear terms and definitions as well as methods for measuring horizontal areas and volumes in buildings and/or parts of buildings, independent of their function.

View
prEN 17756 Archived
Comment end date 2026-10-17
Fertilizers, liming materials and inhibitors - Determination of the chloride content

This document specifies references to methods for the determination of the chloride content in organic fertilizers, organo-mineral fertilizers, inorganic fertilizers, liming materials and inhibitors. This document is applicable to fertilizing product blends where the blend is a mix of at least two of the following components: fertilizers, liming materials, soil improvers, growing media, inhibitors, plant biostimulants, and where the following category: fertilizers is the highest % in the blend by mass or volume, or in the case of liquid form by dry mass. If fertilizer is not the highest % in the blend, the European Standard for the highest % of the blend applies. In case a fertilizing product blend is composed only of inorganic products, the European Standard for inorganic fertilizers applies. NOTE Variations in analytical methods for fertilizing product blends can lead to differing results as some components or matrix interactions can affect the outcome. Validation procedures have shown that developed standard methods are robust and reliable across diverse product compositions, but possible interferences and unexpected results when analysing fertilizing product blends are possible.

View
prEN ISO 11666 Public enquiry
Comment end date 2026-11-12
Non-destructive testing of welds - Ultrasonic testing - Acceptance levels (ISO/DIS 11666:2026)

ISO 11666:2018 specifies two ultrasonic acceptance levels known as acceptance level 2 (AL 2) and acceptance level 3 (AL 3) for full penetration welded joints in ferritic steels, which correspond to ISO 5817:2014, quality levels B and C. An acceptance level corresponding to ISO 5817:2014, quality level D is not included in this document, as ultrasonic testing is generally not requested for this weld quality. These acceptance levels are applicable to testing carried out in accordance with ISO 17640. ISO 11666:2018 applies to the testing of full penetration ferritic steel welds, with thicknesses from 8 mm to 100 mm. It can also be used for other types of welds, materials and thicknesses, provided the tests have been performed with necessary consideration of the geometry and acoustic properties of the component, and an adequate sensitivity can be employed to enable the acceptance levels of this document to be applied. The nominal frequency of probes used in this document is between 2 MHz and 5 MHz, unless attenuation or requirements for higher resolution call for other frequencies. It is important to consider the use of these acceptance levels in conjunction with frequencies outside this range carefully.

Read draft and comment View
EN 1995-3:2025/prA1 Public enquiry
Comment end date 2026-11-12
Eurocode 5 - Design of timber structures - Part 3: Execution

1.1 Scope of EN 1995-3 (1) This document gives minimum requirements for execution of timber structures (buildings and bridges) designed in accordance with EN 1995 (all parts) to ensure that what is built meets the requirements for mechanical resistance, serviceability, durability, and fire performance. (2) This document gives guidance on moisture control during transport to the building site, storage on site, handling on site and erection. (3) This document gives guidance on workmanship and deviation limits during execution. (4) This document assumes that there is an execution specification which states all the specific requirements relevant for the execution of a particular structure. (5) For products covered by a European technical product specification, this document only covers those aspects of fabrication such as cutting, machining and drilling after placement of the product on the market. (6) This document does not cover: a) parts which are not designed according to EN 1995; b) temporary works (such as formwork, scaffolding, propping, shoring, etc.); c) specification, production and conformity of timber members in accordance with European technical product specifications; d) deviation limits for other properties than mechanical resistance, serviceability, durability and fire performance; e) contractual aspects, responsibilities of the various parties, competency requirements or the degree of independence of the personnel undertaking the inspection; f) health and safety requirements during execution. 1.2 Assumptions (1) It is assumed that all relevant provisions of EN 1995 are complied with. (2) It is recognized in this document that areas such as detailed requirements for competence of personnel, and details related to Quality Management are within the competence of the CEN Member States. (3) Before the execution begins on a part of the structure, it is assumed that the following are available on site: — the drawings and specification of that part; — the execution specification. (4) Before the start of the execution, it is assumed that the execution specification has been checked for completeness. (5) It is assumed that previous work (such as foundations) has been inspected and that any work which needs to be done due to deviations from the execution specification has been carried out.

Read draft and comment View
prEN ISO 25178-3 Public enquiry
Comment end date 2026-11-26
Geometrical product specifications (GPS) - Surface texture: Areal - Part 3: Specification operators (ISO/DIS 25178-3:2026)

This part of ISO 25178 specifies the complete specification operator for surface texture (scale limited surfaces) by areal methods.

Read draft and comment View
EN 62148-12:2004/prA2:2026 Public enquiry
Comment end date 2026-12-06
Fibre optic active components and devices - Package and interface standards - Part 12: Laser transmitters with a coaxial RF connector
Read draft and comment View
prEN ISO/IEC 17065 Archived
Comment end date 2026-10-12
Conformity assessment - Requirements for bodies certifying products, processes and services (ISO/IEC FDIS 17065:2026)

This document contains requirements for the competence, consistent operation and impartiality of product, process and service certification bodies. Certification bodies operating to this document need not offer all types of products, processes and services certification. Certification of products, processes and services is a third-party conformity assessment activity (see ISO/IEC 17000:2020, 4.5). In this document, the term “product” can be read as “process” or “service”, except in those instances where separate provisions are stated for “processes” or “services” (see Annex B).

View
EN ISO 683-3:2022/prA1 Public enquiry
Comment end date 2026-10-27
Heat-treatable steels, alloy steels and free-cutting steels - Part 3: Case-hardening steels - Amendment 1 (ISO 683-3:2022/DAM 1:2026)
Read draft and comment View
prEN ISO 15184 Public enquiry
Comment end date 2026-11-12
Paints and varnishes - Determination of film hardness by pencil test (ISO/DIS 15184:2026)

This document specifies a method for determining the film hardness by pushing pencils of known hardness over the film. The test can be performed on a single coating of a paint, varnish or related product, or on the upper layer of a multi-coat system. This rapid test has not been found to be useful in comparing the pencil hardness of different coatings. It is more useful in providing relative ratings for a series of coated panels exhibiting significant differences in pencil hardness. The method is applicable only to smooth surfaces.

Read draft and comment View
EN 1994-1-2:2026/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 4 - Design of composite steel and concrete structures - Part 1-2: Structural fire design

(1) EN 1994-1-2 gives rules for the design of steel-concrete composite structures for the accidental design situation of fire exposure. It only identifies differences from, or supplements to, rules for normal temperature design. (2) EN 1994-1-2 only applies to structures, or parts of structures, that are within the scope of EN1994-1-1 and are designed accordingly.

Read draft and comment View
EN 10205:2024/prA1 Public enquiry
Comment end date 2026-12-06
Cold reduced tinmill products - Blackplate

This document specifies requirements for blackplate product in the form of coils intended for direct use and mostly for the production of electrolytically zinc coated plate, or coils electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS or ECCS-RC). Blackplate can be a single or double reduced product and is specified in nominal thicknesses that are multiples of 0,005 mm from typical 0,10 mm up to 0,60 mm. This document applies to coils in nominal minimum widths of 600 mm. In addition to this document, the general technical delivery conditions of EN 10021 apply. NOTE Standard width coils for specific uses, e.g. tab stock, can be slit into narrow strip for supply in coil form.

Read draft and comment View
prEN 15182-2 Public enquiry
Comment end date 2026-12-05
Portable equipment for projecting extinguishing agents and firefighting support operations - Hand-held branchpipes for fire service use - Part 2: Combination branchpipes PN 16

In addition to the common requirements given in EN 15182 1, this document specifies the specific safety and performance requirements and the corresponding test methods, applicable to hand-held combination branchpipes (nozzles), with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa).

Read draft and comment View
EN 353-2:2024/prA1 Public enquiry
Comment end date 2026-10-22
Personal fall protection equipment - Part 2: Guided type fall arresters including a flexible anchor line

This document specifies requirements, test methods, marking, manufacturer’s instructions and information and packaging for guided type fall arresters including a flexible anchor line forming a single product. This anchor line is attached to an upper anchor point for vertical and inclined applications; for horizontal applications, the anchor point can be located at the user’s foot level. Guided type fall arresters including a flexible anchor line conforming to this document are components of one of the fall arrest systems covered by EN 363:2018. Other types of fall arresters are specified in EN 353-1:2014+A1:2017 or EN 360:2023.

Read draft and comment View
prEN 304 620 V1.0.0 (2026-08) Public enquiry
Comment end date 2026-10-27
Cyber Security (CYBER); CRA; Cybersecurity requirements for Virtual Private Networks (VPNs)
Read draft and comment View
prEN IEC 60255-21:2026 Public enquiry
Comment end date 2026-11-15
Measuring relays and protection equipment - Part 21: Vibration, shock, bump and seismic tests requirements
Read draft and comment View
EN 1993-6:2026/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 3 - Design of steel structures - Part 6: Crane supporting structures

1.1 Scope of EN 1993-6 (1) EN 1993-6 provides rules for structural design of crane supporting structures. (2) EN 1993-6 is applicable to crane supporting structures, especially to indoor and outdoor overhead crane runway beams, of: a) overhead travelling cranes, either: — top-mounted cranes; — underslung cranes; b) monorail hoist blocks. NOTE The principles of the design rules can be applied to supporting structures of other types of cranes making due allowance for differences in the crane-induced actions, if exist. For example, the design rules for supporting structures of the cranes listed in (2) assume that the horizontal crane loads occur randomly scattered along the runways in general. This assumption does not apply to other cranes such as travelling wall jib cranes. (3) EN 1993-6 does not apply to the tracks and suspensions of light crane systems conforming to EN 16851, see Figure 1.1. NOTE The standardized tracks and suspensions of light crane systems are considered as parts of the crane. [Figure 1.1 — Light crane system] (4) Additional rules are given for ancillary runway items including crane rails, structural end stops, surge connectors and surge girders and for runway supporting structures. (5) EN 1993-6 does not apply to cranes and all other moving parts. NOTE Provisions for cranes are given in EN 13001 (all parts) in general and for bridge and gantry cranes in EN 15011 in particular. 1.2 Assumptions (1) Unless specifically stated, EN 1990-1, EN 1991 (all parts) and EN 1993-1 (all parts) apply. (2) The design methods given in EN 1993-6 are applicable if — the execution quality and tolerances are as specified in EN 1090-2, and; — the construction materials and products used are as specified in the relevant parts of EN 1993, or in the relevant material and product specifications. (3) Following interfaces between hoisting device and its supporting structure are assumed: a) the top of crane rail for top-mounted cranes; b) the top of flange on which the crane or hoist block operates for underslung cranes and monorail hoist blocks; c) the support points as shown in Figure 1.1 for light crane systems.

Read draft and comment View
prEN 302 099 V2.3.0 (2026-09) Public enquiry
Comment end date 2026-11-30
Environmental Engineering (EE); Powering of equipment in access network
Read draft and comment View
prEN 15221-10 Public enquiry
Comment end date 2026-12-05
Facility Management - Part 10: Digital Transformation of Facility Management (FM)

This document specifies requirements and provides a framework for the digital transformation of Facility Management (FM). It defines the principles, processes and supporting elements for organizations to apply when planning, implementing and improving digitalization within FM. The purpose of this standard is to ensure that FM organizations can adopt digital practices in a consistent and effective manner that improves operational efficiency, enhances decision-making and strengthens resilience. The standard is written as a companion to EN ISO 41001 [5] Facility management — Management systems — Requirements with guidance for use and EN 15221-8 [2] Facility management — Principles and processes. Its role is not to duplicate the management system requirements of EN ISO 41001 [5] or the principles and processes of EN 15221-8 [2], but to provide the digitalization dimension that complements both. NOTE   Annex B describes the relationship between this document and other standards. This standard applies broadly. It is relevant to: — organizations of any type, size, or sector engaged in FM; — both in-house FM functions and outsourced FM service providers; — all phases of FM service delivery and the asset life cycle. Certain elements are outside the scope of this document. General FM principles and processes are covered in EN 15221-8 [2], while the management system requirements for FM are addressed by EN ISO 41001 [5]. These exclusions ensure that this document remains focused on digital transformation as a distinct, yet integrated, component of FM.

Read draft and comment View
prEN ISO 17072-1 Public enquiry
Comment end date 2026-10-29
Leather - Chemical determination of metal content - Part 1: Extractable metals (ISO/DIS 17072-1:2026)

This document specifies a method for the determination of extractable metals in leather using extraction with an acid artificial-perspiration solution and subsequent determination with inductively coupled plasma optical emission spectrometry (ICP-OES), inductively coupled plasma mass spectrometry (ICP-MS), atomic absorption spectrometry (AAS) or spectrometry of atomic fluorescence (SFA). This method determines extractable metals in leather; it is not compound-specific or specific to the oxidation state of the metals. This method is especially suitable for determining the extractable chromium in chromium-tanned leathers.

Read draft and comment View
prEN 302 186 V2.2.19 (2026-08) Public enquiry
Comment end date 2026-11-01
Satellite Earth Stations and Systems (SES); Aircraft Earth Stations (AESs) operating in the 11/12/14 GHz frequency bands; Harmonised Standard for access to radio spectrum
Read draft and comment View
ISO/DIS 25383 Public enquiry
Comment end date 2026-11-15
Biotechnology — Single cell sequencing — Part 1: Requirements for data processing of RNA-sequencing for eukaryotic cells

This document provides requirements on the workflow and quality assessment of single cell RNA sequencing (scRNA-seq) data processing for eukaryotic cells. This document provides guidelines for raw data quality control, alignment and mapping, and cell barcode correction for single cell RNA sequencing. This document specifies the requirements for visualization and cell type identification of scRNA-seq data.

Read draft and comment View
prEN IEC 63609-2:2026 Public enquiry
Comment end date 2026-11-22
Thermal design of electronics assemblies with miniaturised surface mounting devices and related measurements
Read draft and comment View
EN IEC 60317-25:2020/prA1:2026 Public enquiry
Comment end date 2026-11-20
Amendment 1 - Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200
Read draft and comment View
prEN 302 340 V2.1.19 (2026-09) Public enquiry
Comment end date 2026-12-06
Satellite Earth Stations and Systems (SES); Satellite Earth Stations on board Vessels (ESVs) operating in the 11/12/14 GHz frequency bands allocated to the Fixed Satellite Service (FSS); Harmonised Standard for access to radio spectrum
Read draft and comment View
Total records found: 319
arrow-prev 1 … 6 7 8 9 10 … 13 arrow-next

Quick filters

Organisation
CEN Europos standartizacijos komitetas (159) ISO Tarptautinė standartizacijos organizacija (14) CENELEC Europos elektrotechnikos standartizacijos komitetas (131) ETSI Europos telekomunikacijų standartų institutas (15)
Technical Committee
TK 1 Electronics (34) TK 4 Information technology (4) TK 5 Electrical engineering (42) TK 9 Furniture (2) TK 13 Agricultural engineering (4) TK 18 Telecommunications (15) TK 20 Toys, child use articles, sports and other recreational equipment (1) TK 21 Textiles and personal protective equipment (2) TK 22 Fire safety (7) TK 23 Ceramic tiles, masonry and natural stones (1) TK 24 Quality management and quality assurance (2) TK 25 Matrix, gypsum and gypsum based products (1) TK 26 Thermal insulation materials (1) TK 29 Water supply (16) TK 32 Health (10) TK 35 Safety of machinery (2) TK 36 Environmental protection (2) TK 38 Building constructions (14) TK 39 Protection (2) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (2) TK 41 Welding (8) TK 45 Electric power (6) TK 46 Roofs and building waterproof isolation (6) TK 49 Metallic materials (6) TK 50 Heating and Ventilation Systems (2) TK 51 Food analysis- Horizontal methods (1) TK 56 Metal liquid tanks and industrial pipelines (1) TK 57 Fertilizers (3) TK 59 Geotechnics (3) TK 60 Windows and doors (4) TK 68 Plastics (7) TK 70 Pulp, paper, board, adhesives (1) TK 76 Explosive atmospheres (6) TK 77 Lifts (1) TK 79 IT security techniques (3) TK 80 Road transport and traffic telematics (1) TK 81 Conservation of cultural property (1) TK 82 Safety of trackless overground vehicles (2) TK 86 Geographic information (1) TK 87 Biotechnology (8) TK 88 Building Information Modelling (BIM) (1) TK 89 Risk management and organizational governance (1) TK 91 Asset management and technical maintenance (2) TK 94 Circural economy (1) TK 99 Health Informatics (2)
ICS
Hidrologinės dirvožemio savybės (1) Acid secondary cells and batteries (3) Adhesives (1) Aerospace electric equipment and systems (3) Alarm and warning systems (1) Alcohols. Ethers (1) Aluminium products (1) Amplifiers (3) Anaesthetic, respiratory and reanimation equipment (6) Application of information technology in general (2) Binders. Sealing materials (1) Biology. Botany. Zoology (8) Boilers and heat exchangers (1) Brazing and soldering (1) Building accessories (1) Cellular materials (1) Cement. Gypsum. Lime. Mortar (2) Chemical laboratories. Laboratory equipment (4) Chemicals for purification of water (9) Cleaning appliances (7) Cleanrooms and associated controlled environments (1) Coaxial cables. Waveguides (1) Colour coding (1) Cranes (1) Dental implants (1) Diagnostic equipment (1) Domestic safety (8) Earthworks. Excavations. Foundation construction. Underground works (3) Electric road vehicles (3) Electrical and electronic equipment (2) Electrical and electronic equipment. Control systems (1) Electrical and electronic testing (1) Electrical apparatus for explosive atmospheres (4) Electrical engineering in general (1) Electrical equipment of ships and of marine structure (1) Emission (1) Environment. Health protection. Safety (Vocabularies) (1) Environmental economics. Sustainability (1) Equipment for children (1) Exploratory, drilling and extraction equipment (2) Fertilizers (2) Fibre optic interconnecting devices (1) Fibres and cables (2) Fire protection (1) Fire-fighting (4) Fire-resistance of building materials and elements (1) Floor coverings (2) Food microbiology (1) Forensic science (1) Furniture (2) Fuses and other overcurrent protection devices (2) Gas cylinders (1) Gas heaters (1) Geometrical Product Specification (GPS) (1) Governance and ethics (1) Hand-operated tools (1) Home economics in general (2) Identification cards. Chip cards. Biometrics (1) Immunity (1) Implants for surgery, prosthetics and orthotics (1) Insulators (1) Integrated circuits. Microelectronics (2) Iron and steel pipes (1) IT applications in health care technology (1) IT applications in information, documentation and publishing (1) IT applications in science (2) IT applications in transport (1) IT Security (4) Items of art and handicrafts. Cultural property and heritage (1) Laminated sheets (1) Laundry appliances (2) Leather and furs (2) Lifts. Escalators (1) Lines, connections and circuits (1) Liquid fuels (1) Luminaires (3) Maintenance services. Facilities management (2) Mechanical testing of metals (1) Mining equipment in general (1) Miscellaneous domestic and commercial equipment (1) Multilayer applications (1) Navigation and control equipment (1) Networking (1) Non-ferrous metal pipes (2) Other fluid power system components (1) Other kitchen equipment (1) Other semiconductor devices (2) Other standards related to lamps (1) Paints and varnishes (2) Petroleum products and natural gas handling equipment (1) Pipelines and its parts for district heat (1) Plastics in general (2) Playgrounds (3) Power transmission and distribution networks in general (1) Primary cells and batteries (2) Printed circuits and boards (3) Product and company certification. Conformity assessment (1) Product life-cycles (1) Properties of surfaces (1) Protection against crime (1) Protection against falling and slipping (1) Protective clothing (1) Pumps (2) Radiographic equipment (1) Refrigerating technology (1) Reinforced plastics (1) Relays (1) RF connectors (2) Rivets (1) Road equipment and installations (1) Roofs (1) Safety of machinery (1) Seismic and vibration protection (1) Small craft (2) Smart textiles (1) Stainless steels (2) Stationary containers and tanks (1) Steel structures (3) Sterilization and disinfection in general (1) Sterilizing equipment (1) Surface preparation (4) Technical aspects (6) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (15) Telecontrol. Telemetering (1) Textile fabrics (1) Thermal and sound insulating materials (6) Thermoplastic materials (1) Timber structures (1) Transformers. Reactors (2) Ventilation and air-conditioning systems (1) Ventilators. Fans. Air-conditioners (3) Walls. Partitions. Façades (3) Water heating equipment (2) Water supply systems (7) Welded joints and welds (5) Welding equipment (2) Wires (11)