GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
Total records found: 159
arrow-prev 1 2 3 4 5 … 7 arrow-next
prEN 12909 Public enquiry
Comment end date 2026-11-30
Products used for treatment of water intended for human consumption - Anthracite

This document is applicable to anthracite used for treatment of water intended for human consumption. This document describes the characteristics of anthracite and specifies the requirements and the corresponding test methods for anthracite. This document gives information on the use of anthracite in water treatment.

EN 16611:2023/prA1 Public enquiry
Comment end date 2026-11-28
Furniture - Assessment of the surface resistance to microscratching

This document specifies a method for the assessment of the surface resistance to microscratching and relates to rigid surfaces of all finished products, considering the following exceptions: - Method A is suitable for all types of surface coatings and coverings except for lacquers with pearly or metallic effects. - Method B is suitable for all types of surface. - No method applies to finishes on leather and fabrics. This document is applicable to the test intended to be carried out on a part of finished furniture, but it can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test. It is essential that the test be carried out on unused surfaces.

EN 10205:2024/prA1 Public enquiry
Comment end date 2026-12-06
Cold reduced tinmill products - Blackplate

This document specifies requirements for blackplate product in the form of coils intended for direct use and mostly for the production of electrolytically zinc coated plate, or coils electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS or ECCS-RC). Blackplate can be a single or double reduced product and is specified in nominal thicknesses that are multiples of 0,005 mm from typical 0,10 mm up to 0,60 mm. This document applies to coils in nominal minimum widths of 600 mm. In addition to this document, the general technical delivery conditions of EN 10021 apply. NOTE Standard width coils for specific uses, e.g. tab stock, can be slit into narrow strip for supply in coil form.

prEN 12915-2 Public enquiry
Comment end date 2026-12-06
Products used for the treatment of water intended for human consumption - Granular activated carbon - Part 2: Reactivated granular activated carbon

This document is applicable to reactivated granular activated carbon used for treatment of water intended for human consumption. This document describes the characteristics of reactivated granular activated carbon and specifies the requirements and the corresponding test methods for reactivated granular activated carbon. This document gives information on the use of reactivated granular activated carbon in water treatment.

prEN ISO 3821 Public enquiry
Comment end date 2026-11-26
Gas welding equipment - Rubber hoses for welding, cutting and allied processes (ISO/DIS 3821:2026)

This document specifies requirements for rubber hoses (including twin hoses) for welding, cutting and allied processes. This document specifies requirements for rubber hoses for normal duty of 2 MPa (20 bar) and light duty [limited to hoses for maximum working pressure of 1 MPa (10 bar) and with bore up to and including 6,3 mm]. This document applies to hoses operated at temperatures −20 °C to +60 °C and used in: — gas welding and cutting; — arc welding under the protection of an inert or active gas; — processes allied to welding and cutting, in particular, heating, brazing, and metallization. This document does not specify requirements for hose assemblies; these are detailed in ISO 8207. This document applies neither to thermoplastics hoses nor to hoses used for high pressure [>0,15 MPa (>1,5 bar)] acetylene.

prEN ISO 5359 Public enquiry
Comment end date 2026-11-26
Anaesthetic and respiratory equipment - Low-pressure hose assemblies for use with medical gases (ISO/DIS 5359:2026)

ISO 5359:2014 specifies requirements for low-pressure hose assemblies intended for use with the following medical gases: oxygen, nitrous oxide, medical air, helium, carbon dioxide, xenon, specified mixtures of the gases listed above, oxygen-enriched air, air for driving surgical tools, nitrogen for driving surgical tools, and for use with vacuum. It applies to hose assemblies operating at pressures up to 1 400 kPa and for vacuum systems at pressures not greater than 60 kPa absolute. It does not specify the dimensions and allocation of the gas-specific inlet and outlet connectors for the hose assemblies.It does not specify requirements for coaxial hoses used for the supply and removal of air for driving surgical tools.Nor does it specify the intended uses of hose assemblies.

prEN ISO 18082 Public enquiry
Comment end date 2026-11-26
Anaesthetic and respiratory equipment - Dimensions of non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases (ISO/DIS 18082:2026)

ISO 18082:2014 specifies the dimensions, the allocation and marking of non-interchangeable screw-threaded (NIST) connectors intended to be used at operating pressures up to 1 400 kPa, and for vacuum systems at pressures not greater than 60 kPa absolute. ISO 18082:2014 specifies NIST connectors intended for use with the following medical gases: oxygen; nitrous oxide; medical air; helium; carbon dioxide; xenon; specified mixtures of the gases listed above; oxygen-enriched air; air for driving surgical tools; nitrogen for driving surgical tools; use with vacuum.

prEN ISO 9094 Public enquiry
Comment end date 2026-11-26
Small craft - Fire protection (ISO/DIS 9094:2026)

This document defines a practical degree of fire prevention and protection intended to provide enough time for occupants to escape a fire on board small craft. It applies to small craft having a length of the hull (LH) of up to 24 m except for personal watercraft. This document does not cover: —    the design and installation of permanently installed galley stoves and heating appliances (including components used to distribute the heat) using fuels that are liquid at atmospheric pressure on small craft, which are covered by ISO 14895:2016; —    carbon monoxide detecting systems, which are covered by ISO 12133.

prEN ISO 25178-3 Public enquiry
Comment end date 2026-11-26
Geometrical product specifications (GPS) - Surface texture: Areal - Part 3: Specification operators (ISO/DIS 25178-3:2026)

This part of ISO 25178 specifies the complete specification operator for surface texture (scale limited surfaces) by areal methods.

prEN 1127-2 Public enquiry
Comment end date 2026-11-26
Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining

This document specifies methods for explosion prevention and protection in mining by outlining the basic concepts and methodology for the design and construction of equipment, protective systems and components. This document applies to Group I equipment, protective systems and components intended for use in underground parts of mines and those parts of their surface installations at risk from firedamp and/or combustible dust. NOTE Detailed information on specific equipment, protective systems and components is contained in the relevant individual standards. Safety-relevant data regarding flammable materials and explosive atmospheres are required for the design and construction of the explosion protection measures. This document specifies methods for the identification and assessment of hazardous situations that may lead to explosions and describes the design and construction measures appropriate for the required safety. This is achieved by: — risk assessment; — risk reduction. The safety of equipment, protective systems, and components can be achieved by eliminating hazards and/or limiting the risk, i.e.: a) by appropriate design (without using safeguarding); b) by safeguarding; c) by information for use; d) by any other preventive measures. Measures in accordance with a) (prevention) and b) (protection) against explosions are dealt with in Clause 6 of this document; measures according to c) against explosions are dealt with in Clause 7 of this document. Measures in accordance with d) are not described in this document. They are dealt with in EN ISO 12100:2010, Clause 6. The preventive and protective measures described in this document will not provide the required level of protection unless the equipment, protective systems and components are operated in line with their intended use and are installed and maintained according to the relevant codes of practice or requirements. This document is applicable to any equipment, protective systems and components intended to be used in potentially explosive atmospheres. These atmospheres can arise from flammable materials processed, used or released by the equipment, protective systems and components or from materials in the vicinity of the equipment, protective systems and components and/or from the materials of construction of the equipment, protective systems and components. As shot firing can release potentially explosive atmospheres, this document is also applicable to the equipment used for shot firing, apart from the explosives and detonators. This document is applicable to equipment, protective systems and components at all stages of use. This document is not applicable to: — medical devices intended for use in a medical environment; — equipment, protective systems and components where the explosion hazard results exclusively from the presence of explosives or unstable chemical substances; — equipment, protective systems and components where the explosion can result from reaction of substances with oxidising agents other than atmospheric oxygen or by other hazardous reactions or conditions other than atmospheric conditions; — equipment intended for use in domestic and non-commercial environments where explosive atmospheres may only rarely be created and solely as a result of the accidental leakage of fuel gas; — personal protective equipment covered by Regulation (EU) 2016/425; the design and construction of systems containing desired, controlled combustion processes, unless they can act as ignition sources in potentially explosive atmospheres; — mines where firedamp and/or combustible dust are not naturally present and surface installations such as coal preparation plants, power plants, coke oven plants etc. in which an explosive atmosphere can be present, but which are not part of a coal mine. These are covered by EN 1127-1:2019.

prEN ISO 15883-4 Public enquiry
Comment end date 2026-11-26
Washer-disinfectors - Part 4: Requirements and tests for washer-disinfectors employing chemical disinfection for thermolabile endoscopes (ISO/DIS 15883-4:2026)

This document specifies the particular requirements, including performance criteria for washer-disinfectors (WD) that are intended to be used for cleaning and chemical disinfection of thermolabile endoscopes. This document also specifies the performance requirements for the cleaning and disinfection of the washer-disinfector and its components and accessories which can be required to achieve the necessary performance criteria. The methods, instrumentation and instructions required for type testing, works testing, validation (installation, operational and performance qualification on first installation), routine control and monitoring, and requalification of WD periodically and after essential repairs, are also specified. NOTE 1 In addition, Annex A gives guidance on an appropriate division of responsibility for the range of activities covered by this document. NOTE 2 WD complying with this document can also be used for cleaning and chemical disinfection of other thermolabile re-usable medical devices for which the device manufacturer has recommended and validated this method of disinfection. WD complying with the requirements of this document are not intended for cleaning and disinfection of medical devices, including endoscopic accessories, which are heat stable and can be disinfected or sterilized by thermal methods (see ISO 15883-1:2006+Amd 1:2014, 4.1.5). The specified performance requirements of this document do not ensure the inactivation or removal of the causative agent(s) (prion protein) of transmissible spongiform encephalopathies. NOTE 3 If it is considered that prion protein might be present, particular care is needed in the choice of cleaning agents and disinfectants to ensure that the chemicals used do not react with the prion protein and/or other protein in a manner that can inhibit its removal or inactivation from the load or washer-disinfector. NOTE 4 This document can be used by prospective purchasers and manufacturers as the basis of agreement on the specification of the WD, manufacturers of endoscopes, cleaning products, and disinfecting products.

prEN ISO 5667-3 Public enquiry
Comment end date 2026-11-24
Water quality - Sampling - Part 3: Preservation and handling of water samples (ISO/DIS 5667-3:2026)

This document specifies the general requirements for sampling, preservation, handling, transport and storage of all water samples for physicochemical, chemical, hydrobiological and microbiological analyses and determination of radiochemical analytes and activities. Guidance on the validation of storage times of water samples is provided in ISO/TS 5667-25 [2]. This document is not applicable to water samples intended for ecotoxicological assays, biological assays (which is specified in ISO 5667-16 [4]), passive sampling (which is specified in ISO 5667-23 [5]) and microplastics (which is specified in ISO 5667-27 [6]). This document is particularly appropriate when samples cannot be analysed on site and have to be transported to a laboratory for analysis.

prEN 1487 Public enquiry
Comment end date 2026-11-23
Building valves - Hydraulic safety groups - Tests and requirements

This document specifies dimensions, materials and performance requirements, including methods of test, for hydraulic safety groups, of nominal sizes from DN 15 to DN 25, having working pressures from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Hydraulic safety groups are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95 °C. Hydraulic safety groups limit the pressure in hot water heaters, prevent the backflow of water into the main circuit and prevent the discharged water to get into contact with the water in the water heater. Hydraulic safety groups do not control the temperature. They ensure the hydraulic safety of water heaters if the mechanical resistance of the water heater remains at least equal to the rating pressure. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

prEN ISO/IEEE 11073-10441 Public enquiry
Comment end date 2026-11-21
Health informatics - Device interoperability - Part 10441: Device specialization - Cardiovascular fitness and activity monitor (ISO/IEEE FDIS 11073-10441:2026)

Within the context of the ISO/IEEE 11073 family of standards for device communication, a normative definition of communication between personal telehealth cardiovascular fitness and activity monitor devices and managers (e.g., cell phones, personal computers, personal health appliances, and set top boxes) is established in this standard in a manner that enables plug-and-play interoperability. Appropriate portions of existing standards are leveraged including ISO/IEEE 11073 terminology, information models, application profile standards, and transport standards. The use of specific term codes, formats, and behaviors in telehealth environments restricting optionality in base frameworks in favor of interoperability is specified. A common core of communication functionality for personal telehealth cardiovascular fitness and activity monitor devices is defined in this standard.

prEN ISO 17078-1 Public enquiry
Comment end date 2026-11-21
Oil and gas industries including lower carbon energy - Drilling, production and injection equipment - Part 1: Side-pocket mandrels (ISO/DIS 17078-1:2026)

ISO 17078:2004 provides requirements for side-pocket mandrels used in the petroleum and natural gas industry. This part of ISO 17078 includes specifying, selecting, designing, manufacturing, quality control, testing, and preparation for shipping of side-pocket mandrels. This part of ISO 17078:2004 does not address nor include requirements for end connections between the side-pocket mandrels and the well conduit. The installation and retrieval of side-pocket mandrels is outside the scope of this part of ISO 17078:2004. Additionally, this part of ISO 17078:2004 does not include specifications for centre-set mandrels, or mandrels that employ or support tubing-retrievable flow control devices. This part of ISO 17078:2004 does not include gas-lift or any other flow-control valves or devices, latches, and/or associated wire line equipment that can or cannot be covered in other ISO specifications. The side-pocket mandrels to which this part of ISO 17078:2004 refers are independent devices that can accept installation of flow-control or other devices down-hole.

prEN 14359 Public enquiry
Comment end date 2026-11-21
Gas-loaded accumulators for fluid power applications

1.1 This document specifies the requirements for materials, design, manufacture, testing inspection, safety equipment configuration and documentation (including instructions for first operation), for commonly-used types of gas-loaded accumulators and pressure vessels used to provide additional gas capacity for fluid power applications (see 1.2). 1.2 This document applies to the following types of components, defined as the pressure-containing envelope of gas-loaded accumulators: - bladder type; - diaphragm type; - piston type; - transfer type; - pressure vessels used to provide additional gas capacity. They consist of one or several parts joined together by a variety of mechanical means and by welding. 1.3 This document applies to gas-loaded accumulators which operate with the following conditions: - subject to an internal gauge pressure greater than 0,5 bar; - working temperature not lower than –50 °C and not higher than +200 °C; - containing all liquids and gases as defined in the European Legislation on Pressure Equipment, see Note. NOTE When the accumulator contains Group 1 liquids or gases, consideration relating to risks other than those required by the European Legislation on Pressure Equipment are not covered by this document and will be assessed separately.

EN 1994-1-2:2026/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 4 - Design of composite steel and concrete structures - Part 1-2: Structural fire design

(1) EN 1994-1-2 gives rules for the design of steel-concrete composite structures for the accidental design situation of fire exposure. It only identifies differences from, or supplements to, rules for normal temperature design. (2) EN 1994-1-2 only applies to structures, or parts of structures, that are within the scope of EN1994-1-1 and are designed accordingly.

EN 1994-2:2026/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 4 - Design of composite steel and concrete structures - Part 2: Bridges

EN 1994-2 gives design rules for steel-concrete composite bridges or members of bridges, supplementary to the general rules given in EN 1994-1-1.

EN 1994-1-1:2026/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 4 - Design of composite steel and concrete structures - Part 1-1: General rules and rules for buildings

1.1 Scope of EN 1994-1-1 (1) EN 1994-1-1 gives general rules for the design of steel and concrete composite structures and supplementary provisions specific for buildings. NOTE Specific rules for bridges are given in EN 1994-2. 1.2 Assumptions (1) The assumptions of EN 1990-1 apply to EN 1994-1-1. (2) In addition to the general assumptions of EN 1990-1, the assumptions given in EN 1992-1-1, EN 1992-1-2, and EN 1993-1-1 apply to this document. (3) EN 1994-1-1 is intended to be used in conjunction with EN 1990-1, EN 1991 (all parts), EN 1992-1-1, EN 1993 (all parts), EN 1997 (all parts), EN 1998 (all parts when steel and concrete composite structures are built in seismic regions), EN 1090-1, EN 1090-2, EN 1090-4, EN 13670 and ENs for construction products relevant to steel and concrete composite structures.

EN 1993-6:2026/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 3 - Design of steel structures - Part 6: Crane supporting structures

1.1 Scope of EN 1993-6 (1) EN 1993-6 provides rules for structural design of crane supporting structures. (2) EN 1993-6 is applicable to crane supporting structures, especially to indoor and outdoor overhead crane runway beams, of: a) overhead travelling cranes, either: — top-mounted cranes; — underslung cranes; b) monorail hoist blocks. NOTE The principles of the design rules can be applied to supporting structures of other types of cranes making due allowance for differences in the crane-induced actions, if exist. For example, the design rules for supporting structures of the cranes listed in (2) assume that the horizontal crane loads occur randomly scattered along the runways in general. This assumption does not apply to other cranes such as travelling wall jib cranes. (3) EN 1993-6 does not apply to the tracks and suspensions of light crane systems conforming to EN 16851, see Figure 1.1. NOTE The standardized tracks and suspensions of light crane systems are considered as parts of the crane. [Figure 1.1 — Light crane system] (4) Additional rules are given for ancillary runway items including crane rails, structural end stops, surge connectors and surge girders and for runway supporting structures. (5) EN 1993-6 does not apply to cranes and all other moving parts. NOTE Provisions for cranes are given in EN 13001 (all parts) in general and for bridge and gantry cranes in EN 15011 in particular. 1.2 Assumptions (1) Unless specifically stated, EN 1990-1, EN 1991 (all parts) and EN 1993-1 (all parts) apply. (2) The design methods given in EN 1993-6 are applicable if — the execution quality and tolerances are as specified in EN 1090-2, and; — the construction materials and products used are as specified in the relevant parts of EN 1993, or in the relevant material and product specifications. (3) Following interfaces between hoisting device and its supporting structure are assumed: a) the top of crane rail for top-mounted cranes; b) the top of flange on which the crane or hoist block operates for underslung cranes and monorail hoist blocks; c) the support points as shown in Figure 1.1 for light crane systems.

EN 1993-1-6:2025/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 3 - Design of steel structures - Part 1-6: Strength and stability of shell structures

1.1 Scope (1) EN 199316 provides rules for the structural design of plated steel structures that have the form of a shell of revolution (axisymmetric shell). (2) This document is applicable to unstiffened fabricated axisymmetric shells formed from isotropic rolled plates using both algebraic and computational procedures, and to stiffened axisymmetric shells with different wall constructions using computational procedures. It also applies to associated circular or annular plates and to beam section rings and stringer stiffeners where they form part of the complete shell structure. The general computational procedures are applicable to all shell forms. (3) This document does not apply to manufactured shells or to shell panels or to elliptical shell forms, except that its computational procedures are applicable to all shell structures. This document does not apply to structures under seismic or other dynamic loading. It does not cover the aspects of leakage of stored liquids or solids. (4) Cylindrical and conical panels are not explicitly covered by this document. However, the provisions of 9.8 can be used provided that appropriate boundary conditions are taken into account. (5) This document defines the characteristic and design values of the resistance of the structure. (6) This document is concerned with the requirements for design against the ultimate limit states of: — plastic failure; — cyclic plasticity; — buckling; — fatigue. (7) Overall equilibrium of the structure (sliding, uplifting, overturning) is not included in this document. Special considerations for specific applications are included in the relevant application parts of EN 1993. (8) Detailed formulae for the simple calculation of unstiffened cylinders, cones and spherical domes are given in the Annexes. (9) Provisions for simple calculations on specific stiffened shell types are given in EN 199341. (10) This document is intended for application to steel shell structures. Where no standard exists for shell structures made of other metals, including high strength steels, the provisions of this document are applicable provided the appropriate material properties of the metal are taken into account. (11) The provisions of this document are intended to be applied within the temperature ranges defined in the relevant EN 1993 application parts. (12) Where no application part defines a different range, this document applies to structures within the following limits: — design metal temperatures lie within the range −50 °C to +100 °C, except when using the special provisions given in 5.1; — radius to thickness ratios (r/t) within the range 50 to 2 000; — manufactured circular hollow sections according to EN 10210 and EN 10219 are outside the scope of this document and are covered by EN 199311. However, if no other provisions are available, the rules of this document are useful for manufactured circular hollow sections. In particular, this document is applicable to the design of manufactured piles (see EN 19935) provided the imperfections and tolerance requirements of EN 19935 are adopted in place of those specified in this document, and where no other standard covers the specific pile geometry. NOTE 1 Experimental and theoretical data relating to manufactured circular hollow sections were not considered when this document was drafted. The application of this document to such structures therefore remains the responsibility of the user. NOTE 2 The stress design rules of this document can be rather conservative if applied to some geometries and loading conditions for relatively thickwalled shells. NOTE 3 Thinner shells than r/t = 2 000 can be treated using these provisions but the provisions have not been verified for such thin shells. NOTE 4 The maximum temperature is restricted so that the influence of creep can be ignored where high temperature creep effects are not covered by the relevant application part. [...]

EN 1993-4-1:2026/prA1 Public enquiry
Comment end date 2026-11-19
Eurocode 3 - Design of steel structures - Part 4-1: Silos

1.1 Scope of EN 1993 4 1 (1) prEN 1993 4 1 provides rules for the structural design of steel silos of circular or rectangular plan-form, being free-standing (on ground) or supported on a structural framework (elevated). (2) prEN 1993 4 1 is applicable to silos constructed from isotropic rolled plates that are stiffened or unstiffened, from corrugated sheeting that is stiffened or unstiffened and from flat or corrugated plates assembled into box structures of different geometries. It applies to vertical walls, hoppers, roof structures, transition junctions and support structures. (3) prEN 1993 4 1 does not apply to storage vessels for silage and haylage, or to the storage of materials that are not free-flowing (see EN 1991 4). This Part 4-1 also does not cover: - resistance to fire; - cylindrical silos with internal subdivisions; - internal structures within a single silo (except for internal ties, as defined in 12.5); - silos with capacity less than 100 kN (10 tonnes); - hoppers that are supported on a structural framework; - cases where special measures are necessary to limit the consequences of accidents. (4) This document is applicable to silos within the following dimensional limits (see EN 1991-4): - Silo aspect ratio hb/dc < 10 - Silo total height hb < 70 m - Silo equivalent diameter dc < 60 m NOTE These dimensional limitations are more limited than those of EN 1991-4 which also applies to silos constructed from other materials. (5) Where this standard applies to circular planform silos, the geometric form is restricted to axisymmetric structures, but unsymmetrical actions on them and supports that induce forces in the silo structure that are not axisymmetric are included. (6) This part is concerned only with the requirements for resistance and stability of steel silos. For other requirements (such as operational safety, functional performance, fabrication and erection, quality control, details like man-holes, flanges, filling devices, outlet gates and feeders, etc.), see other relevant standards and information. (7) This part is concerned with both isolated silo structures and silos that are connected to others to form a battery of silos, but throughout this document the term silo refers to a single cell within a battery. (8) Provisions relating to special requirements of seismic design are provided in EN 1998 4, which complements or adapts the provisions of Eurocode 3 specifically for this purpose. (9) The structural design of supporting structures for the silo are dealt with in EN 1993 1 1. The supporting structure is deemed to consist of all structural elements beneath the bottom flange of the lowest ring of the silo (see Figure 1.1), though information on some forms of support structure is given in Clause 8 of this document. (10) Foundations in reinforced concrete for steel silos are dealt with in EN 1992 (all parts) and EN 1997 (all parts). 1.2 Assumptions (1) Unless specifically stated, the provisions of EN 1990, EN 1991 (all parts) and EN 1993 1 (all parts) apply. (2) The design methods given in EN 1993 4 1 are applicable if: - the execution quality is as specified in EN 1090 2, and - the construction materials and products used are as specified in the relevant parts of EN 1993 (all parts), or in the relevant material and product specifications. Figure 1.1 - Terminology used in silo structures ...

prEN ISO 25379-2 Public enquiry
Comment end date 2026-11-19
In vitro diagnostic Next Generation Sequencing (NGS) workflows - Part 2: Human RNA examination (ISO/DIS 25379-2:2026)

This document specifies requirements and gives recommendations for next generation sequencing (NGS) workflows. This document covers the pre-examination processes, human RNA isolation, sequencing library preparation, sequencing, sequence analysis and reporting of the examination of sequences for diagnostic purposes from isolated RNA from, e.g. formalin-fixed and paraffin embedded tissues, fresh frozen tissues, fine needle aspirates (FNA), whole blood, circulating tumour cells (CTCs), exosomes and other extracellular vesicles, and circulating cell free RNA from plasma. NOTE 1 Typical applications include, but are not limited to, NGS for oncology and clinical genetics, certain single-cell analyses. This document is addressing in vitro diagnostic examinations including laboratory developed tests and is applicable to medical laboratories, molecular pathology laboratories and molecular genetic laboratories, in vitro diagnostic developers and manufacturers, biobanks as well as institutions and organizations performing biomedical research or sequencing services. This document is not applicable for in situ sequencing, forensic sequencing, sequencing of pathogens or microorganisms and microbiome analysis. NOTE 2 International, national or regional regulations or requirements or multiples of them can also apply to specific topics covered in this document.

prEN ISO 11403-3 Public enquiry
Comment end date 2026-11-15
Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO/DIS 11403-3:2026)

This document specifies test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments: — prolonged exposure to heat; — liquid chemicals; — environmental stress cracking under a constant tensile stress; — artificial weathering. The tests are listed in order of increasing severity of the environment. By testing under the least severe environments first, it is possible to make informed judgements regarding whether tests under more severe conditions are worthwhile.

prEN 13126-5 Public enquiry
Comment end date 2026-11-14
Building hardware - Hardware for windows and door height windows - Requirements and test methods - Part 5: Devices that restrict the opening of windows and door height windows

This document specifies requirements and test methods for durability, strength, security and function of devices that restrict the opening of windows and door height windows to a maximum opening width. Depending on the requirements imposed in Member States on the basis of building regulations or in tenders for window or door height windows, the hardware manufacturer designs the restrictors to allow opening widths of for example max. 89 mm, max. 100 mm or max. 120 mm; for the use of restrictors in building components. This document does not apply to a) restrictors with an opening width limitation of more than 120 mm; b) child protective window restrictors intended to be installed by the end consumers; such restrictors from the DIY market are covered in EN 16281; c) restrictors for window designs with sliding sashes. NOTE 1 Restrictors and reverse restrictors can be either a separate item of hardware or an integral part of hardware, for example a part of the operating gear or an integral part of a hinge. NOTE 2 It is possible to use more than one restrictor on a single window. NOTE 3 The requirements included within this document take the needs for child safety into consideration. This document applies to restrictors that are intended to be factory installed in windows and door height windows by specialist companies in their production facilities.

Total records found: 159
arrow-prev 1 2 3 4 5 … 7 arrow-next

Quick filters

Technical Committee
TK 1 Electronics (34) TK 4 Information technology (4) TK 5 Electrical engineering (42) TK 9 Furniture (2) TK 13 Agricultural engineering (4) TK 18 Telecommunications (15) TK 20 Toys, child use articles, sports and other recreational equipment (1) TK 21 Textiles and personal protective equipment (2) TK 22 Fire safety (7) TK 23 Ceramic tiles, masonry and natural stones (1) TK 24 Quality management and quality assurance (2) TK 25 Matrix, gypsum and gypsum based products (1) TK 26 Thermal insulation materials (1) TK 29 Water supply (16) TK 32 Health (10) TK 35 Safety of machinery (2) TK 36 Environmental protection (2) TK 38 Building constructions (14) TK 39 Protection (2) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (2) TK 41 Welding (8) TK 45 Electric power (6) TK 46 Roofs and building waterproof isolation (6) TK 49 Metallic materials (6) TK 50 Heating and Ventilation Systems (2) TK 51 Food analysis- Horizontal methods (1) TK 56 Metal liquid tanks and industrial pipelines (1) TK 57 Fertilizers (3) TK 59 Geotechnics (3) TK 60 Windows and doors (4) TK 68 Plastics (7) TK 70 Pulp, paper, board, adhesives (1) TK 76 Explosive atmospheres (6) TK 77 Lifts (1) TK 79 IT security techniques (3) TK 80 Road transport and traffic telematics (1) TK 81 Conservation of cultural property (1) TK 82 Safety of trackless overground vehicles (2) TK 86 Geographic information (1) TK 87 Biotechnology (8) TK 88 Building Information Modelling (BIM) (1) TK 89 Risk management and organizational governance (1) TK 91 Asset management and technical maintenance (2) TK 94 Circural economy (1) TK 99 Health Informatics (2)
ICS
Hidrologinės dirvožemio savybės (1) Acid secondary cells and batteries (3) Adhesives (1) Aerospace electric equipment and systems (3) Alarm and warning systems (1) Alcohols. Ethers (1) Aluminium products (1) Amplifiers (3) Anaesthetic, respiratory and reanimation equipment (6) Application of information technology in general (2) Binders. Sealing materials (1) Biology. Botany. Zoology (8) Boilers and heat exchangers (1) Brazing and soldering (1) Building accessories (1) Cellular materials (1) Cement. Gypsum. Lime. Mortar (2) Chemical laboratories. Laboratory equipment (4) Chemicals for purification of water (9) Cleaning appliances (7) Cleanrooms and associated controlled environments (1) Coaxial cables. Waveguides (1) Colour coding (1) Cranes (1) Dental implants (1) Diagnostic equipment (1) Domestic safety (8) Earthworks. Excavations. Foundation construction. Underground works (3) Electric road vehicles (3) Electrical and electronic equipment (2) Electrical and electronic equipment. Control systems (1) Electrical and electronic testing (1) Electrical apparatus for explosive atmospheres (4) Electrical engineering in general (1) Electrical equipment of ships and of marine structure (1) Emission (1) Environment. Health protection. Safety (Vocabularies) (1) Environmental economics. Sustainability (1) Equipment for children (1) Exploratory, drilling and extraction equipment (2) Fertilizers (2) Fibre optic interconnecting devices (1) Fibres and cables (2) Fire protection (1) Fire-fighting (4) Fire-resistance of building materials and elements (1) Floor coverings (2) Food microbiology (1) Forensic science (1) Furniture (2) Fuses and other overcurrent protection devices (2) Gas cylinders (1) Gas heaters (1) Geometrical Product Specification (GPS) (1) Governance and ethics (1) Hand-operated tools (1) Home economics in general (2) Identification cards. Chip cards. Biometrics (1) Immunity (1) Implants for surgery, prosthetics and orthotics (1) Insulators (1) Integrated circuits. Microelectronics (2) Iron and steel pipes (1) IT applications in health care technology (1) IT applications in information, documentation and publishing (1) IT applications in science (2) IT applications in transport (1) IT Security (4) Items of art and handicrafts. Cultural property and heritage (1) Laminated sheets (1) Laundry appliances (2) Leather and furs (2) Lifts. Escalators (1) Lines, connections and circuits (1) Liquid fuels (1) Luminaires (3) Maintenance services. Facilities management (2) Mechanical testing of metals (1) Mining equipment in general (1) Miscellaneous domestic and commercial equipment (1) Multilayer applications (1) Navigation and control equipment (1) Networking (1) Non-ferrous metal pipes (2) Other fluid power system components (1) Other kitchen equipment (1) Other semiconductor devices (2) Other standards related to lamps (1) Paints and varnishes (2) Petroleum products and natural gas handling equipment (1) Pipelines and its parts for district heat (1) Plastics in general (2) Playgrounds (3) Power transmission and distribution networks in general (1) Primary cells and batteries (2) Printed circuits and boards (3) Product and company certification. Conformity assessment (1) Product life-cycles (1) Properties of surfaces (1) Protection against crime (1) Protection against falling and slipping (1) Protective clothing (1) Pumps (2) Radiographic equipment (1) Refrigerating technology (1) Reinforced plastics (1) Relays (1) RF connectors (2) Rivets (1) Road equipment and installations (1) Roofs (1) Safety of machinery (1) Seismic and vibration protection (1) Small craft (2) Smart textiles (1) Stainless steels (2) Stationary containers and tanks (1) Steel structures (3) Sterilization and disinfection in general (1) Sterilizing equipment (1) Surface preparation (4) Technical aspects (6) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (15) Telecontrol. Telemetering (1) Textile fabrics (1) Thermal and sound insulating materials (6) Thermoplastic materials (1) Timber structures (1) Transformers. Reactors (2) Ventilation and air-conditioning systems (1) Ventilators. Fans. Air-conditioners (3) Walls. Partitions. Façades (3) Water heating equipment (2) Water supply systems (7) Welded joints and welds (5) Welding equipment (2) Wires (11)