Standartų projektų sąrašas

prEN IEC 60794-2-50:2026 Viešoji apklausa

Komentavimo iki data 2026-12-18

Optiniai skaiduliniai kabeliai. 2-50 dalis. Vidaus kabeliai. Viengyslių ir dvigyslių kabelių, naudojamų kabelių sąrankose su jugtimis abiejuose galuose, šeimos specifikacija

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 14509-5 Viešoji apklausa

Komentavimo iki data 2026-11-08

Gamyklinės iš abiejų pusių metalu aptaisytos sluoksninės izoliacinės plokštės. 5 dalis. Projektavimo metodai

This document specifies design methods for combination of actions and spans for factory made double skin metal faced insulating sandwich panels (hereafter sandwich panels). The sandwich panels are for use in self-supporting and structural applications in roofs, in external and internal walls (including partitions) and in ceilings in buildings as well as those in cold store applications. This document covers uniformly distributed loads, line loads perpendicular to the span over the full width of the panel and thermal gradients, it gives no information about normal forced axially loaded sandwich panels, torsional loaded sandwich panels or sandwich panels as a part of a diaphragm.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 489-1 Viešoji apklausa

Komentavimo iki data 2026-10-24

Centralizuoto šilumos tiekimo vamzdžiai. Neardomai izoliuotų vieno ir dviejų vamzdžių sistemos, skirtos požeminiams karšto ir šalto vandens tinklams. 1 dalis. Karšto ir šalto vandens tinklų metalinių vamzdžių jungčių apvalkalai ir šiluminė izoliacija, atitinkanti EN 13941 serijos standartus

This document specifies requirements and test methods for joint casing systems for single and twin pipes between adjacent factory-made pipe, and/or fitting and/or valve assemblies for buried heating and cooling water networks with rigid pipe systems with metal service pipes in accordance with EN 13941-1 [4] and EN 13941-2 [5] as well as rigid pipe systems with plastic service pipes according to series EN 17415 and flexible pipe systems with metal service pipes according to EN 15632-4 . NOTE There are no differences in requirements for single and twin pipe joint casing systems. For bedding materials other than those defined in 5.2.3 additional precautions are defined inEN 13941-2 [5].

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 301 908-26 V1.0.0 (2026-08) Viešoji apklausa

Komentavimo iki data 2026-11-09

IMT koriniai tinklai. Prieigos prie radijo ryšio spektro darnusis standartas. 26 dalis. Orlaivyje esanti vartotojo įranga (VĮ)

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63758-5-3:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Qi specifikacija. 2.3 versija. 5-3 dalis. MPP. Magnetinių elementų konstrukcija

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 21043-2 Viešoji apklausa

Komentavimo iki data 2026-12-12

Teismo ekspertizė. 2 dalis. Teismo ekspertizės proceso ir ekspertizės objektų gavimo bei tvarkymo bendrieji reikalavimai (ISO/DIS 21043-2:2026)

This document specifies general requirements and recommendations for the operation of the forensic service provider. These apply throughout the forensic process, both at a scene and within a facility. This document also contains requirements and provides recommendations for the recovery and management of items. These requirements and recommendations are designed to ensure that: — items are preserved; — personnel are competent; — equipment and consumables are suitable; — health and safety risks are mitigated. This document is applicable to all areas of expertise of forensic science; however, it is not applicable to the recovery of digital data, which is covered by ISO/IEC 27037.[1] The storage medium itself can yield additional items (e.g. fingermarks or DNA) which would be covered by this document.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 1888-1 Viešoji apklausa

Komentavimo iki data 2026-10-31

Vaiko priežiūros gaminiai. Vaikų vežimėliai. 1 dalis. Sėdimieji vežimėliai ir gulimieji vežimėliai

This document specifies the safety requirements and test methods for pushchairs and prams, designed for the carriage of one or more children, up to 22 kg each and up to 20 kg for any integrated platform on which a child can stand. This document does not cover toys, baby carriers fitted with wheels; pushchairs and prams propelled by a motor and pushchairs and prams designed for children with special needs. Where a pushchair or pram or any part of the pushchair or pram has several functions or can be converted into another function it is due to comply with relevant standard(s).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO/IEC 23282 Viešoji apklausa

Komentavimo iki data 2026-11-07

Dirbtinis intelektas. Tiksliųjų natūraliosios kalbos apdorojimo sistemų įvertinimo metodai (ISO/IEC DIS 23282:2026)

This document specifies the evaluation of natural language processing systems, in the sense of measuring the quality of a system’s results to assess its functional suitability. It provides a definition of evaluation methods for those systems, together with guidance on how to select, implement and interpret those evaluation methods. This document covers quantitative metrics as well as other evaluation methods. It includes requirements on the implementation of the described metrics, and further requirements on the technical resources involved in the evaluation process.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63466-1:2026 Viešoji apklausa

Komentavimo iki data 2026-11-15

Plyšiniai bangolaidžiai. 1 dalis. Bendroji specifikacija. Bendrieji reikalavimai ir bandymo metodai

This part of IEC 63466 specifies the general requirements and test methods for leaky waveguides, including terms and definitions, design and structure, type designation, ratings and characteristics, identification, marking and labelling, requirements and test methods, etc. This document is applicable to leaky waveguides, including rigid rectangular leaky waveguides and elliptic leaky waveguides. These leaky waveguides are intended for use in tunnels, railways, highways, subways, elevators and other installations in which conventional antenna transmission is not satisfactory or even impossible.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63758-3:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Qi specifikacija. 2.3 versija. 3 dalis. Galios tiekimas

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 50763:2026 Viešoji apklausa

Komentavimo iki data 2026-12-13

Lankstaus elektros tiekimo paslaugų vertinimas, susijęs su elektros tinklo valdymu

This document aims at standardizing concepts, terms and definitions relating to electrical flexibility as well as methodology to assess electrical flexibility services. The purpose of this document is to define a standardized characterization of electrical flexible services, so that data collected by transmission system operators or distribution system operators can be used and compared in an interoperable manner. In addition to the development of relevant use cases, the project will focus on the following normative aspects: — definition and characterization of the different types of electrical flexibilities depending, in particular, on the flexibility needs and the response time; — activation or control mode of the flexibility services; — measurement provisions: e.g. consistency with the data of the electricity smart meters and the metrology requirements and the use of dedicated measurement devices; — information exchanges between concerned parties; — verification of delivery of service.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 15154-6 Viešoji apklausa

Komentavimo iki data 2026-11-05

Avariniai saugos dušai. 6 dalis. Prie vandentiekio tinklo prijungti ne laboratorijoms skirti dušai su daugeliu purkštukų

This document is a product specification, giving performance requirements for plumbed-in multiple nozzle emergency safety body showers which are permanently connected to a water supply and installed on industrial and logistic sites. Emergency safety body showers using fluid other than water are not considered in this document. This document also specifies requirements in respect of installation, adjustment and marking of the showers as well as operation and maintenance instructions to be given by the manufacturer. NOTE 1 Plumbed-in emergency safety body showers designed for laboratory facilities are dealt with in EN 15154-1. NOTE 2 Water overhead body showers for sites other than laboratories are dealt with in FprEN 15154-5. NOTE 3 Attention is drawn to national regulations which can apply in respect of the installation and use of emergency safety showers.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63439-2-1:2026 Viešoji apklausa

Komentavimo iki data 2026-11-08

Elektros gamybos, perdavimo ir skirstymo sistemų robotinė technika. 2-1 dalis. Bendrieji techniniai reikalavimai, keliami elektros perdavimo oro linijas tikrinančioms bepiločių orlaivių sistemoms

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-79:2026 Viešoji apklausa

Komentavimo iki data 2026-11-08

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-79 dalis. Ypatingieji reikalavimai, keliami didelio slėgio ir gariniams valytuvams

This standard deals with the safety of high-pressure cleaners without traction drive, intended for household and commercial indoor or outdoor use, having a rated pressure not less than 2,5 MPa and not exceeding 35 MPa. It also applies to steam cleaners and those parts of hot water high pressure cleaners incorporating a steam stage which have a capacity not exceeding 100 l, a rated pressure not exceeding 2,5 MPa and a product of capacity and rated pressure not exceeding 5 MPa·l. They are not equipped with a traction drive. The following power systems of the drive for the high pressure pump are covered: - mains powered motors up to a rated voltage of 250 V for single-phase machines and 480 V for other machines, - battery-operated motors, - internal combustion engines, - hydraulic or pneumatic motors. This standard does not apply to: - high pressure water jet machines having a rated pressure exceeding 35 MPa; - liquid or steam cleaners intended for domestic use (IEC 60335-2-54); - hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series); - appliances for medical purposes (IEC 60601); - agricultural sprayers (ISO 4254-6); - non-liquid, solid abrasive cleaners; - machines designed to be part of a production process; - machines designed for use in corrosive or explosive environments (dust, vapour or gas); - machines designed for use in vehicles or on board of ships or aircraft.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63559:2026 Viešoji apklausa

Komentavimo iki data 2026-11-15

Koncentriškai susukti oro linijų elektros laidai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 21304-2 Viešoji apklausa

Komentavimo iki data 2026-12-05

Plastikai. Ypač didelės molekulinės masės polietileno (PE-UHMW) liejimo ir ekstruzijos medžiagos. 2 dalis. Bandinių paruošimas ir savybių nustatymas (ISO/DIS 21304-2:2026)

This document specifies the methods of preparation of test specimens and the test methods to be used for determining the properties of ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials. It establishes general principles for handling test materials and for conditioning both the test materials before moulding and the specimens before testing. This document specifies procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made. Properties and test methods which are suitable and necessary to characterize PE-UHMW moulding and extrusion materials are established. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for or of particular significance to these moulding and extrusion materials are also included in this document, as are the designatory properties specified in ISO 21304-1. This document specifies the-materials with MFR less than 0,1 g/10 min at 190 °C /21,6 kg based on ISO 17855-1. The methods of preparation and conditioning, the specimen dimensions and the test procedures specified in this document are used in order to obtain reproducible and comparable test results. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-14:2026 Viešoji apklausa

Komentavimo iki data 2026-12-13

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-14 dalis. Ypatingieji reikalavimai, keliami virtuvės aparatams

This European Standard deals with the safety of electric kitchen machines for household and similar purposes, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60079-101:2026 Viešoji apklausa

Komentavimo iki data 2026-10-25

Sprogiosios atmosferos. 101 dalis. Apsaugos nuo sprogimo principai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN IEC 60317-27-3:2019/prA2:2026 Viešoji apklausa

Komentavimo iki data 2026-11-06

Kai kurių tipų apvijinių laidų techniniai reikalavimai. 27-3 dalis. Popieriaus juosta dengtas stačiakampis varinis laidas. 2 keitinys

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-109:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-109 dalis. Ypatingieji reikalavimai, keliami vandens apdorojimo ultravioletine spinduliuote prietaisams

This European Standard deals with the safety of UV radiation water treatment appliances for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances including direct current (DC) supplied appliances and battery-operated appliances

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60269-100:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Žemosios įtampos saugikliai. 100 dalis. Bendrieji reikalavimai ir bandymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 16119-4 Viešoji apklausa

Komentavimo iki data 2026-12-10

Žemės ir miškų ūkio mašinos. Aplinkosauginiai purkštuvams keliami reikalavimai. 4 dalis. Stacionarieji ir pusiau stacionarūs purkštuvai (ISO/DIS 16119-4:2026)

This part of ISO 16119 specifies requirements and the means for their verification for the design and performance of fixed and semi-mobile sprayers, as defined in 3.1 and 3.2, with regard to minimizing the potential risk of environmental contamination during use, including misuse foreseeable by the manufacturer. This type of spraying system is generally a combination of separate elements (main tank, pump and application unit) that can be assembled in fixed installations (fixed sprayers) or with moving parts (semi-mobile sprayers). It does not apply to application equipment for space/spatial treatments. It is intended to be used with ISO 16119 1, which gives general requirements common to all the sprayer types covered by ISO 16119. When requirements of this part of ISO 16119 are different from those stated in ISO 16119 1, the requirements of this part of ISO 16119 take precedence over the requirements of ISO 16119 1 for machines within the scope of this part of ISO 16119. This part of ISO 16119 does not cover safety aspects (see ISO 4254 6). • Filling - Total tank extra volume • Quick coupler for CTS + mandatory provision of inductor hopper or CTS • Filters drain valve • Digital level indicator + accuracy • Pump requirements as per ISO 12908: 2020 • Residue concentration only one method for system rinsing

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 472-3 Viešoji apklausa

Komentavimo iki data 2026-12-12

Plastikai. Aiškinamasis žodynas. 3 dalis. Plastikų suvirinimas ir šiluminis sujungimas (ISO/DIS 472‑3:2026)

The ISO 472 series defines terms used in the plastics industry, including terms and definitions appearing in the plastics standards of ISO/TC 61 and general terms and definitions of polymer science used in all aspects of plastics technology. This document defines terms used in the plastics standards of ISO TC61/SC11 Plastics Products and relevant terms applied in the area of welding (including solvent welding) and thermal staking.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 12452 Viešoji apklausa

Komentavimo iki data 2026-11-08

Varis ir vario lydiniai. Valcuoti briaunotieji besiūliai vamzdžiai šilumokaičiams

This document specifies the composition, property requirements and tolerances on dimensions and form for rolled, finned, seamless copper and copper alloy tubes for heat exchangers. It is applicable to copper and copper alloy tubes supplied in the size range from 6 mm up to and including 35 mm outside diameter; from 1 mm up to and including 3,5 mm wall thickness of the unfinned section; and with fin height up to and including 4,5 mm. The sampling procedures and the methods of testing for verification of conformity to the requirements of this document are also specified.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 60317-13:2010/prA2:2026 Viešoji apklausa

Komentavimo iki data 2026-11-06

Kai kurių tipų apvijinių laidų techniniai reikalavimai. 13 dalis. 200 klasės poliesteriu ar poliesterimidu dengtas ir poliamido imidu emaliuotas apvalusis varinis laidas. 2 keitinys

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Standartų projektų sąrašas

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS