Standartų projektų sąrašas

Paieškos frazė

Išplėstinė paieška

Žymuo

Direktyvos

Organizacija

ICS

Technikos komitetas

Užsienio komitetas

Darbo grupė

Etapas

Būsena

Komentavimo data

iki

Rezultatai

prEN 1538 Viešoji apklausa

Komentavimo iki data 2026-11-05

Specialiųjų geotechnikos darbų atlikimas. Tranšėjinės sienos

This European Standard establishes general principles for the execution of diaphragm walls as either retaining walls or cut-off walls. NOTE 1 This standard covers only structures constructed in a trench excavated with a support fluid or in dry conditions, where soil is removed and replaced by concrete or slurry and with wall thickness B ≥ 40 cm. NOTE 2 Diaphragm walls can be permanent or temporary structures. NOTE 3 The following types of structure are considered: a) retaining walls: usually constructed to support the sides of an excavation in the ground. They include: 1) cast in situ concrete diaphragm walls; 2) precast concrete diaphragm walls; 3) reinforced slurry walls; b) cut-off walls: usually constructed to prevent migration of groundwater, clear or polluted, or of other contaminants present in the ground. They include: 1) slurry walls (possibly with membranes or sheet piles); 2) plastic concrete walls. NOTE 4 Walls formed shallow vertical trenches (typically excavations with a ratio of depth over thickness D/B < 5 or D < 5 m) are not covered by this standard.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 1536 Viešoji apklausa

Komentavimo iki data 2026-11-05

Specialiųjų geotechnikos darbų atlikimas. Gręžtiniai poliai

1.1 This European Standard establishes general principles for the execution of bored piles (see 3.2). NOTE 1 This standard covers piles or barrettes which are formed in the ground by excavation and are structural members used to transfer actions and/or limit deformations. NOTE 2 This standard covers piles with circular cross-section (see Figures 1 and A.1a)) and barrettes (see 3.3) with rectangular, T or L or any other similar cross-section (see Figure 2) concreted in a single operation. NOTE 3 In the standard the term pile is used for circular cross-section structure and the term barrette for other shapes. Both are bored piles. 1.2 This European Standard applies to bored piles (see Figure 3) with: - uniform cross-section (straight shaft); - telescopically changing shaft dimensions; - excavated base enlargements; or - excavated shaft enlargements. NOTE The shape of a pile base and of an enlargement depends on the tool used for the excavation. 1.3 This European Standard applies (see Note) to: - bored piles with a depth to width ratio  5; - piles (see Figures 1 and 3) with a shaft diameter 0,3 m  D  3,0 m; - barrettes (see Figure 2) with the least dimension Wi  0,4 m, a ratio LBiB / Wi between its largest and its least dimensions  6 and a cross-sectional area A  15 m²; - piles with circular precast elements used as structural member (see Figure 7) with a least dimension DP  0,3 m; - barrettes with rectangular precast elements used as structural member with a least dimension WP  0,3 m. NOTE The standard covers a large range of diameters. For small diameter bored piles less than 450 mm, the general specification can be adapted to cater for the lack of space (e.g. minimum bars number and spacing). 1.4 This European Standard applies to piles with the following rake (see Figure 4): - n  4 (  76°); - n  3 (  72°) for permanently cased piles. (...)

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 14731 Viešoji apklausa

Komentavimo iki data 2026-10-29

Specialiųjų geotechnikos darbų atlikimas. Grunto apdorojimas giluminiu vibravimu

This document establishes general principles for the execution of soil treatment by deep vibration. The following types of treatment are covered by this document: - deep vibratory compaction to densify the ground as mentioned in EN 1997 3:2025, Annex I, Table I.1; - vibrated columns formed by inserted granular material laterally/radially compacted against the surrounding ground to form a stiff composite column-soil structure (vibrated compacted granular columns) as mentioned in EN 1997 3:2025, Annex I, Table I.2; - vibrated columns formed by inserted material developing unconfined compressive strength comprising a composite of binder and granular material (rigid columns) as mentioned in EN 1997 3:2025, Annex I, Table I.2. The following treatment methods are covered by this document: - methods in which depth vibrators, containing oscillating weights which cause horizontal vibrations, are inserted into the ground; - methods in which compaction probes are inserted into the ground using a vibrator, which remains above ground surface, and which oscillates in a vertical mode. Treatment methods are outlined in Annexes A, B, C and D. The following treatment methods, among others, are not included in this document: - dynamic compaction, dynamic replacement and other methods in which some form of treatment is applied to the ground surface; - uncompacted granular columns primarily used as drains; - explosive compaction.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS