Standartų projektų sąrašas

prEN 1129 Viešoji apklausa

Komentavimo iki data 2026-12-10

Baldai. Atlenkiamosios lovos. Saugos reikalavimai ir bandymų metodai

This document specifies safety requirements and test methods for foldaway beds for domestic and non-domestic use. The requirements are only applicable to the foldaway function of the bed. The safety, strength and durability of the bed itself, including high beds and bunk beds, as well as other functions e.g. seating, tables or storage, are covered by other European Standards. Safety that is dependent upon the structure of the building is not included. It does not include requirements for electrical safety. It does not include requirements for the resistance to ageing, degradation and flammability. The requirements are applicable without regard to materials, design, construction or manufacturing process. This document does not apply to folding beds, camping beds and convertible bed/chairs or settees which are covered by other European safety standards.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 16003 Viešoji apklausa

Komentavimo iki data 2026-12-13

Chemikalai žmonėms vartoti skirtam vandeniui ruošti. Kalcio-magnio karbonatas

This European Standard is applicable to calcium magnesium carbonate used for treatment of water intended for human consumption. It describes the characteristics of calcium magnesium carbonate and specifies the requirements and the corresponding test methods for calcium magnesium carbonate. It gives information on its use in water treatment.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 16004 Viešoji apklausa

Komentavimo iki data 2026-12-07

Chemikalai žmonėms vartoti skirtam vandeniui ruošti. Magnio oksidas

This European Standard is applicable to magnesium oxide used for treatment of water intended for human consumption. It describes the characteristics of magnesium oxide and specifies the requirements and the corresponding test methods for magnesium oxide. It gives information on its use in water treatment.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 16409 Viešoji apklausa

Komentavimo iki data 2026-12-13

Chemikalai žmonėms vartoti skirtam vandeniui ruošti. Dolomitinės kalkės

This European Standard is applicable to Dolomitic lime used for treatment of water intended for human consumption. It describes the characteristics of magnesium oxide and specifies the requirements and the corresponding test methods for Dolomitic lime. It gives information on its use in water treatment.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 18052:2025/prA1 Viešoji apklausa

Komentavimo iki data 2026-12-06

Intelektinės transporto sistemos. El. sauga. Pagalbos iškvietos sistemos (eCall) visos grandinės atitikties testavimas, taikomas eCall aukšto lygmens taikomųjų programų protokolams (HLAP), naudojamiems mišrioje perjungiamųjų linijų tinklų ir paketinio ryšio tinklų aplinkoje

This document describes the key actors in the eCall chain of service provision in hybrid circuit switched/packet switched network environments as: 1) In-Vehicle System (IVS)/vehicle, 2) Mobile Network Operator (MNO), 3) Public Safety Answering Point (PSAP), and to provide conformance tests for actor groups 1) – 3). NOTE 1 Conformance tests are not appropriate nor required for vehicle occupants, although they are the recipient of the service. NOTE 2 Third party eCall systems (TPS-eCall) are not within the scope of this deliverable. This is because the core TPS-eCall standard (EN 16102) does not specify the communications link between the vehicle and the TPS service provider. NOTE 3 These conformance tests are partly based on the appropriate conformance tests from EN 16454 and CEN/prEN 17240. This deliverable therefore adapts and revises Conformance Test Protocols (CTP) from EN 16454 and CEN/prEN 17240 for hybrid circuit switched/packet switched network environments. This document complements EN 16454 and CEN/prEN 17240 and provides a suite of conformance tests for IVS equipment, MNOs and PSAPs, required to ensure and demonstrate compliance with CEN/prEN 17905. The scope covers conformance testing of new engineering developments, products and systems, and does not imply testing associated with individual installations in vehicles or locations.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 527-6 Viešoji apklausa

Komentavimo iki data 2026-12-06

Plastikai. Tempimo savybių nustatymas. 6 dalis. Atsitiktine tvarka orientuotomis kapotomis sluoksnelėmis arba stiklo pluoštu armuotų plastikų kompozitų deformacijų pasiskirstymo matavimas (ISO/DIS 527-6:2026)

This document outlines methods for measuring the strain distribution for randomly oriented chopped strand- or fibre-reinforced plastic composites, based upon the general principles given in ISO 527-4. The methods are used to statistically evaluate the inherent variation of strain-based properties. The main purpose of this document compared to existing standards is to evaluate the strain distribution due to the random orientation of chopped fibres, while ISO 527-4 is sufficient for evaluating only the bulk elastic modulus. This standard provides two methods for evaluating an inherent strain distribution of the material, Method A as using DIC analysis system and Method B as using several strain gauges with a short gauge length. The methods are suitable for use with fibre-reinforced thermosetting and thermoplastic composites incorporating discontinuous or chopped reinforcements such as mats, chopped strands or tapes, long-fibre injection or combination of such reinforcements. The methods are not normally suitable for continuous fibre-reinforced materials which generate homogeneous strain distribution on the surface of the test specimen.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 3682-001 Viešoji apklausa

Komentavimo iki data 2026-12-05

Aerospace series - Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 °C continuous - Part 001: Technical specification

This document specifies the general characteristics, the conditions for qualification, acceptance and quality assurance, as well as the test programs and groups for connectors intended for use in a temperature range from - 65 °C to 150 °C continuous.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 3682-002 Viešoji apklausa

Komentavimo iki data 2026-12-05

Aerospace series - Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 °C continuous - Part 002: Specification of performance and contact arrangements

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 10416 Viešoji apklausa

Komentavimo iki data 2026-12-05

Naftos ir dujų pramonė, įskaitant mažesnio anglies dioksido pėdsako energijos gamybą. Gręžimo tirpalai. Laboratoriniai bandymai (ISO/DIS 10416:2026)

ISO 10416:2008 provides procedures for the laboratory testing of both drilling-fluid materials and drilling-fluid physical, chemical and performance properties. It is applicable to both water-based and oil-based drilling fluids, as well as the base or “make-up” fluid. ISO 10416:2008 is not applicable as a detailed manual on drilling fluid control procedures. Recommendations regarding agitation and testing temperature are presented because the agitation history and temperature have a profound effect on drilling fluid properties.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 19186-1 Viešoji apklausa

Komentavimo iki data 2026-12-05

Geografinė informacija. GeoSPARQL. 1 dalis. RDF duomenims skirta geografinių užklausų kalba (ISO/DIS 19186-1:2026)

Vienna agreement

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 25086-2 Viešoji apklausa

Komentavimo iki data 2026-12-05

Tekstilė. Audinių atsparumo siūlų ištraukimui nustatymas. 2 dalis. Besisukančios bandymo kameros su adatėlėmis metodas (ISO/DIS 25086-2:2026)

This document describes a test method for the determination of snagging resistance of a fabric using pins fitted in a rotating chamber.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 12814-3 Viešoji apklausa

Komentavimo iki data 2026-12-06

Termoplastikinių pusgaminių suvirintųjų jungčių bandymai. 3 dalis. Tempiamojo valkšnumo bandymas

This document specifies the dimensions, the method of sampling, the preparation of the test specimens and the conditions for performing the tensile creep test perpendicular to the weld in order to determine the long-term tensile welding factor. A tensile creep test may be used in conjunction with other tests (e.g. bend test, tensile test, macrographic examination, …) to assess the performance of welded assemblies made from thermoplastics materials. The test is applicable to welded assemblies made from thermoplastics materials, filled or unfilled such as tubes and fittings, sheets, plates and profiles, but not reinforced, irrespective of the welding process used.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 15182-3 Viešoji apklausa

Komentavimo iki data 2026-12-05

Gesinimo medžiagų purškimo ir pagalbinių gaisro gesinimo operacijų kilnojamoji įranga. Gaisrų gesinimo tarnybų naudojami rankiniai švirkštai. 3 dalis. Kompaktinės čiurkšlės ir (arba) pastovaus kampo išsklaidytosios čiurkšlės PN 16 švirkštai

In addition to the common requirements given in EN 15182-1, this document specifies the specific safety and performance requirements and the corresponding test methods, applicale to hand-held branchpipes with smooth bore and/or one fixed spray jet angle with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa). NOTE 1 These branchpipes offer no or inadequate protection for firefighters when the spray jet angle is less than 30 ° and therefore are not adapted in high risk firefighting situations such as internal attack. NOTE 2 These branchpipes are not adapted when fighting fires in or near electrical installations when the spray jet angle is less than 30° without written authorization in the manual (safety distances included).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 15182-2 Viešoji apklausa

Komentavimo iki data 2026-12-05

Gesinimo medžiagų purškimo ir pagalbinių gaisro gesinimo operacijų kilnojamoji įranga. Gaisrų gesinimo tarnybų naudojami rankiniai švirkštai. 2 dalis. Keičiamos čiurkšlės PN 16 švirkštai

In addition to the common requirements given in EN 15182 1, this document specifies the specific safety and performance requirements and the corresponding test methods, applicable to hand-held combination branchpipes (nozzles), with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 15182-4 Viešoji apklausa

Komentavimo iki data 2026-12-05

Gesinimo medžiagų purškimo ir pagalbinių gaisro gesinimo operacijų kilnojamoji įranga. Gaisrų gesinimo tarnybų naudojami rankiniai švirkštai. 4 dalis. Didelio slėgio PN 40 švirkštai

In addition to common the requirements given in EN 15182 1, this document specifies the specific safety and performance requirements and the corresponding test methods, applicable to hand-held high pressure branchpipes (nozzles) with a nominal pressure of 40 bar (4,0 MPa) PN 40, with a maximum flow rate up to 250 l/min at a reference pressure of 6 bar (0,6 MPa). These branchpipes are used for example for quick attack lines, building fires, forest fires, etc.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 15182-1 Viešoji apklausa

Komentavimo iki data 2026-12-05

Gesinimo medžiagų purškimo ir pagalbinių gaisro gesinimo operacijų kilnojamoji įranga. Gaisrų gesinimo tarnybų naudojami rankiniai švirkštai. 1 dalis. Bendrieji reikalavimai

This document specifies the minimum common safety and performance requirements of hand-held branchpipes used by fire and rescue service equipment. This document defines: - test methods; - classification and designation; - instructions for use and maintenance; marking. NOTE The additional specific requirements applicable to hand-held branchpipes are defined in EN 15182-2:— (combination branchpipes PN 16), EN 15182-3:— (Smooth bore and/or one fixed spray jet angle branchpipes PN 16) and EN 15182-4:— (High pressure branchpipes PN 40). This document is not applicable to: - branchpipes covered by the EN 671 series; - foam branchpipes covered by EN 16712-3; - CAFS branchpipes; - powder branchpipes; - branchpipes with a maximum working pressure above 40 bar.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 13497 Viešoji apklausa

Komentavimo iki data 2026-12-05

Statybiniai termoizoliaciniai gaminiai. Išorinių sudėtinių termoizoliacinių sistemų atsparumo smūgiui nustatymas

This document specifies the equipment and procedure for determining the resistance to impact of ETICS kits with renders.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 15221-10 Viešoji apklausa

Komentavimo iki data 2026-12-05

Infrastruktūros valdymas. 10 dalis. Pastatų valdymo skaitmeninė transformacija

This document specifies requirements and provides a framework for the digital transformation of Facility Management (FM). It defines the principles, processes and supporting elements for organizations to apply when planning, implementing and improving digitalization within FM. The purpose of this standard is to ensure that FM organizations can adopt digital practices in a consistent and effective manner that improves operational efficiency, enhances decision-making and strengthens resilience. The standard is written as a companion to EN ISO 41001 [5] Facility management — Management systems — Requirements with guidance for use and EN 15221-8 [2] Facility management — Principles and processes. Its role is not to duplicate the management system requirements of EN ISO 41001 [5] or the principles and processes of EN 15221-8 [2], but to provide the digitalization dimension that complements both. NOTE Annex B describes the relationship between this document and other standards. This standard applies broadly. It is relevant to: — organizations of any type, size, or sector engaged in FM; — both in-house FM functions and outsourced FM service providers; — all phases of FM service delivery and the asset life cycle. Certain elements are outside the scope of this document. General FM principles and processes are covered in EN 15221-8 [2], while the management system requirements for FM are addressed by EN ISO 41001 [5]. These exclusions ensure that this document remains focused on digital transformation as a distinct, yet integrated, component of FM.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 21304-2 Viešoji apklausa

Komentavimo iki data 2026-12-05

Plastikai. Ypač didelės molekulinės masės polietileno (PE-UHMW) liejimo ir ekstruzijos medžiagos. 2 dalis. Bandinių paruošimas ir savybių nustatymas (ISO/DIS 21304-2:2026)

This document specifies the methods of preparation of test specimens and the test methods to be used for determining the properties of ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials. It establishes general principles for handling test materials and for conditioning both the test materials before moulding and the specimens before testing. This document specifies procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made. Properties and test methods which are suitable and necessary to characterize PE-UHMW moulding and extrusion materials are established. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for or of particular significance to these moulding and extrusion materials are also included in this document, as are the designatory properties specified in ISO 21304-1. This document specifies the-materials with MFR less than 0,1 g/10 min at 190 °C /21,6 kg based on ISO 17855-1. The methods of preparation and conditioning, the specimen dimensions and the test procedures specified in this document are used in order to obtain reproducible and comparable test results. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 18283 Viešoji apklausa

Komentavimo iki data 2026-12-05

Dirbtinis intelektas. DI sistemų šališkumo valdymo sąvokos, priemonės ir reikalavimai

This document defines concepts, measures and requirements for assessment and treatment of bias in AI systems. This includes bias unwanted by the AI Provider and AI Deployer according to their specification of the AI system, in the context of the AI Act. This encompasses consideration of data bias including any data used to build or assess the AI system, but also system or model bias that can result from algorithmic factors, such as algorithm design choices.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 15384 Viešoji apklausa

Komentavimo iki data 2026-11-20

Apsauginė ugniagesių apranga. Gamtinių teritorijų gaisrų gesinimo aprangos laboratoriniai bandymo metodai ir eksploatacinių charakteristikų reikalavimai (ISO/DIS 15384:2025)

This document specifies methods of test and minimum performance requirements for personal protective clothing, designed to protect the wearer's body, except for the head, hands, and feet, that is worn during wildland firefighting and associated activities. This clothing is not intended to provide protection during fire entrapment. This document covers the general design of the garment, the minimum level of performance for the materials employed and the methods of test to determine these levels. This document is not applicable to clothing for use in situations encountered in structural firefighting (EN 469 or ISO 11999-3), rescue (ISO 18639) or where a high level of infrared radiation is expected (ISO 15538 or EN 1486), nor does this document cover clothing to protect against chemical, biological, electrical or radiation hazards. This document does not provide protection against high mechanical risks such as for protection when using chain saws.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 14644-7 Viešoji apklausa

Komentavimo iki data 2026-12-03

Švarūs kambariai ir su jais susijusi kontroliuojamoji aplinka. 7 dalis. Skiriamosios priemonės (ISO/DIS 14644-7:2026)

ISO 14644-7:2004 specifies the minimum requirements for the design, construction, installation, test and approval of separative devices, in those respects where they differ from cleanrooms as described in ISO 14644-4 and 14644-5. The application of ISO 14644-7:2004 takes into account the following limitations: user requirements are as agreed by customer and supplier; application-specific requirements are not addressed; specific processes to be accommodated in the separative-device installation are not specified; fire, safety and other regulatory matters are not considered specifically; where appropriate, national and local regulations apply. ISO 14644-7:2004 is not applicable to full-suits.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 8339 Viešoji apklausa

Komentavimo iki data 2026-12-03

Pastatų ir inžinerinių statinių sandarikliai. Tempiamųjų savybių nustatymas (tempimas iki nutrūkimo) (ISO/DIS 8339:2026)

ISO 8339:2005 specifies a method for the determination of the tensile properties of sealants used in joints in building construction.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 16883 Viešoji apklausa

Komentavimo iki data 2026-12-03

Kultūros paveldo išsaugojimas. Istorinių pastatų energinių charakteristikų gerinimo gairės

This document provides guidelines for sustainably improving the energy performance of historic buildings, e.g. historically, architecturally or culturally valuable buildings, while respecting their significance. The use of this document is not limited to buildings with statutory heritage designation, it applies to historic buildings of all types and ages. This document presents a normative working procedure for selecting measures to improve energy performance, based on an investigation, analysis and documentation of the building including its significance. The procedure assesses the impact of those measures in relation to preserving the character-defining elements of the building.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 438-2 Viešoji apklausa

Komentavimo iki data 2026-11-30

Didelio slėgio apdailos laminatai (HPL). Lakštai termoreaktyviųjų dervų pagrindu (paprastai vadinami laminatais). 2 dalis. Savybių nustatymas

This document specifies the methods of test for determination of the properties of high-pressure decorative laminates as defined in Clause 3. These methods are primarily intended for testing the sheets specified in EN 438-3, EN 438-4, EN 438-5, EN 438-6, EN 438-8, and EN 438-9. The precision of the test methods, specified in this document, is not known because inter-laboratory data are not yet available. When inter-laboratory data will be obtained, precision statements will be added to the test method at the following revision. For those test methods having an end point determination based on subjective judgement, it is not meaningful to make a statement of precision.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Standartų projektų sąrašas

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS